• Brands
  • Company
  • Contact
EN / UK
Type Code Seach | *NOT READY*
#CODE
Keyword suggestions
Part number suggestions
Discontinued Products

Motor shafts / stepped on one side / with collar / machining selectable

Motor shafts / stepped on one side / with collar / machining selectable

Click on this image to zoom in.

Click on this image to zoom in.

  • Motor shafts / stepped on one side / with collar / machining selectable
  • Motor shafts / stepped on one side / with collar / machining selectable
  • Motor shafts / stepped on one side / with collar / machining selectable

MISUMI

MISUMI

Data sheet

Part Number

Once your search is narrowed to one product,
the corresponding part number is displayed here.

Dimensional Drawing

Driving Shaft - One End Stepped Shoulder Type: Related Image

[ ! ]ℓ = L－ (LA+LB+T)[ ! ]LA+LB+T ≤ L/2
[!] The shaft may have centering holes on ends.
[!] There is an undercut 1.5 mm or less in width and 0.3 mm or less in depth on the stepped part.
* Ds: Tap dimension of Bearing Inner Race.

DTolerance
h6		Circularity M
80
-0.009		0.003
10
12·12 A0
-0.011
15
17·17 A
200
-0.013
250.005
30
350
-0.016
40
45
 
TypeD, P, Q ToleranceConcentricity[M] Material[H]Hardness[S] Surface Treatment
KZFNh6⌀0.01EN 1.1191 Equiv.——
KZFCBlack Oxide
KZFPElectroless Nickel Plating
KZFSEN 1.4301 Equiv.—
KZFFEN 1.1191 Equiv.Induction Hardened—
Surface Hardness 50HRC or more

Specification Table

Part Number—L—T—P—LA—Q—LB
KZFN30—350—T20—P30—LA50—Q25—LB30
Part Number0.5 mm IncrementsSelection1 mm Increments0.5 mm Increments1 mm Increments0.5 mm IncrementsH* Ds
TypeDLTPLAQLB
KZFN
KZFC
KZFP
KZFS
KZFF		850.0 to 220.05
10
15
20		6 to 94.0 to 40.05 to 74.0 to 40.01210
1050.0 to 300.08 to 125.0 to 50.07 to 95.0 to 50.01513
1210 to 135.0 to 60.07 to 115.0 to 60.014
12 A10
15
20
25		12 to 182016
15100.0 to 400.012 to 185.0 to 75.010 to 145.0 to 75.018
1714 to 185.0 to 100.010 to 165.0 to 100.019
17 A14 to 202521
2017 to 2314 to 1924
25100.0 to 500.010
20
30
40
50		20 to 2810.0 to 125.014 to 2410.0 to 125.03029
3025 to 3315.0 to 150.020 to 2915.0 to 150.03534
3528 to 3820 to 344039
40200.0 to 500.035 to 4720.0 to 150.020 to 3920.0 to 150.05048
4535 to 4820 to 4449

Alterations

Part Number—L—T—P—LA—Q—LB—(MA, NA, KA, TA, SA, etc.)
KZFF30—300—T20—P30—LA60—Q25—LB60—MMA30 － MMB30 － KA10 － HA45 － KB10 － HB40
AlterationsCodeSpec.
Left EndRight End

Threaded Ends

Driving Shaft - One End Stepped Shoulder Type: Related Image		MA
MSA
MMA		MB
MSB
MMB

MD
MSD
MMD

Adds threads at shaft ends. Specify the length of the threads. (Accuracy, coarse or fine threads differ depending on the current ordering code.)
Ordering Code MA15-MSB15 1 mm Increments 5 ≤ Thread Length ≤ M × 5, LA (LB)-2

 
CodeScrew Accuracy
Left EndRight End
MAMBMDCoarseJIS 6h (Class 2)
MSAMSBMSDFine (Standard Grade)JIS 6h (Class 2)
MMAMMBMMDFine (Precision Grade)JIS 4h (Class 1)

[!] When D, P, Q = M, thread length can be specified.

[!] Specify Q diameter smaller than MD, MSD and MMD root diameter.

M (Coarse)PitchM (Fine)PitchM (Fine)Pitch
M50.8M50.5M251.5
M61.0M60.75M301.5
M81.25M80.75M351.5
M101.5M100.75M401.5
M121.75M121.0M451.5
M202.5M151.0  
M243M171.0  
M303.5M201.0  
M364    

Tapped Ends

Driving Shaft - One End Stepped Shoulder Type: Related Image		NANB

Adds taps on shaft ends. Select the thread diameter.
Ordering Code NA5-NB5 [!] NA, NB ≤ P (Q)-4

NA (Coarse), NB (Coarse)
Selection
M3 M4 M5 M6 M8
M10 M12 M16 M20
M24

Keyway Machining

Driving Shaft - One End Stepped Shoulder Type: Related Image		KAKB
KC
KD		Adds a keyway. Specify the position and the length of the keyway.
Ordering Code KA10-HA30-KB100-HB50
KA, HA, KB, HB, KC, HC, KD, HD = 1 mm Increments
[ ! ]3 ≤ HA,HB,HC,HD ≤ 100
[!]When more than 2 keyways are added, the tolerances may shift by up to 0.2°.
[!] Specify the keyway position more than 2 mm away from the shouldered or stepped part.

Keyway Machining + Set Screw Flat

Driving Shaft - One End Stepped Shoulder Type: Related Image		ZAZB
ZC
ZD

Adds a flat at any designated angle based on the keyways. Specify the position and the length for each keyway, and the angle for the set screw flats.
Ordering CodeZA40-HA20-AA90
ZA, HA, ZB, HB, ZC, HC, ZD, HD = 1 mm Increments AA, AB, AC, AD = 30° Increments 30° ≤ AA, AB, AC, AD ≤ 330°
[!] 3 ≤ HA, HB, HC, HD ≤ 100 [!] Specify the keyway position more than 2 mm away from the shouldered or stepped part.

·Specification Code

Keyway
Position Specified		Keyway
Width Specified		Angle Configurable
30° Increments
ZAHAAA
ZBHBAB
ZCHCAC
ZDHDAD
D·P·Q56 to 1718 to 4041 to 48
H0.5123

[!] The length of each set screw flat is the same as that of each keyway.
[!] For a keyway and the angle of a set screw flat, the tolerances may shift by up to ± 0.2°.

Retaining Ring Groove

Driving Shaft - One End Stepped Shoulder Type: Related Image		TATB
TD
Adds a retaining ring groove. Specify the position of a retaining ring groove.
Ordering Code TA10-TB100
TA, TB, TD = 1 mm Increments 4 ≤ TA (TB) ≤ LA (LB)-3
[!] Retaining rings are included.

[ NG ]P,Q = 27,31,33,34,36 to 39,
Not available for 41 to 44, 46 to 48.

P,Q,D ≤ 8: Retaining Ring Type E P, Q ≥ 9, D ≥ 10: Retaining Ring Type C

Driving ShaftsRetaining Ring
[M] Material[H]Hardness[S] Surface Treatment[M] Material
EN 1.1191 Equiv.——Spring Steel
Black Oxide
Electroless Nickel PlatingEN 1.4301 Equiv. (CSP)
EN 1.4301 Equiv.—
EN 1.1191 Equiv.Surface 50HRC or more—Spring Steel

Wrench Flats

Driving Shaft - One End Stepped Shoulder Type: Related Image		SA
SH		SB

Adds wrench flats. Specify the position of a wrench flat.
Ordering Code SA5-SB10-SH SA, SB = 1 mm Increments SA, SB ≥ 0 SA ≤ LA-ℓ, SB ≤ LB-ℓ
[!] Specification of the length for SH is not necessary. Adds wrench flats on the shoulder. (ℓ = h)

 
D810121517202530354045
W78101314172227303638
ℓ8101520
 
P·Q5678 to 1011 to 1314 to 1516 to 1819 to 2122 to 2526 to 2829 to 3132 to 3738 to 4142 to 4546 to 48
W1455.571013141719222730363841
ℓ8101520

2 Set Screw Flats (Angle Specified)

Driving Shaft - One End Stepped Shoulder Type: Related Image		WAWB
WD

Adds a flat at any designated angle besides the datum plane 0°.
Specify the position, the length and the angle of the set screw flats. When 0° is specified, only one set screw flat is machinable.
Ordering Code WA15-GA10-AA0
WA, WB, WD, GA, GB, GD = 1 mm Increments AA, AB, AC = 30° Increments 0° ≤ AA, AB, AC ≤ 330°

·Specification Code

Set Screw Flat
Position Specification		Set Screw Flat
Width Specification		Angle Configurable
30° Increments
WAGAAA
WBGBAB
WDGDAC
D·P·Q56 to 1718 to 4041 to 48
H0.5123

Tolerance Change

Driving Shaft - One End Stepped Shoulder Type: Related Image		DJ (js6)
DK (k6)

Changes the D dimension tolerance to js6 or k6.
Ordering Code DJ or DK


·About KZFF (Induction Hardened)

When alterations on the above are specified,
the shafts are induction hardened after machining. (Except the threaded sections)
As a result, these may occur:
(1): Due to thermal conduction to the thread, the threads may be hardened by 2 to 3 mm. (2): Induction Hardened may shrink the keyway width (Around -0.01 to -0.02)
If the key becomes hard to fit, adjust it by gauging.

Part Number:  

    3D preview is not available, because the part number has not yet been determined.

  • In order to open the 3D preview, the part number must be fixed.
Loading...

Plug-in is required for 3D Preview

CAD Download

Data to be displayed
30
45
60
  1. 1
  2. 2
  3. Next >>
Part Number
KZFC8-[50-219/0.5]-T[5,​10,​15,​20]-P[6-9/1]-LA[4-40/0.5]-Q[5-7/1]-LB[4-40/0.5]
KZFC10-[50-300/0.5]-T[5,​10,​15,​20]-P[8-12/1]-LA[5-50/0.5]-Q[7-9/1]-LB[5-50/0.5]
KZFC12-[50-300/0.5]-T[5,​10,​15,​20]-P[10-13/1]-LA[5-60/0.5]-Q[7-11/1]-LB[5-60/0.5]
KZFC12A-[50-300/0.5]-T[10,​15,​20,​25]-P[12-18/1]-LA[5-60/0.5]-Q[7-11/1]-LB[5-60/0.5]
KZFC15-[100-400/0.5]-T[10,​15,​20,​25]-P[12-18/1]-LA[5-75/0.5]-Q[10-14/1]-LB[5-75/0.5]
KZFC17-[100-400/0.5]-T[10,​15,​20,​25]-P[14-18/1]-LA[5-100/0.5]-Q[10-16/1]-LB[5-100/0.5]
KZFC17A-[100-400/0.5]-T[10,​15,​20,​25]-P[14-20/1]-LA[5-100/0.5]-Q[10-16/1]-LB[5-100/0.5]
KZFC20-[100-400/0.5]-T[10,​15,​20,​25]-P[17-23/1]-LA[5-100/0.5]-Q[14-19/1]-LB[5-100/0.5]
KZFC25-[100-500/0.5]-T[10,​20,​30,​40,​50]-P[20-28/1]-LA[10-125/0.5]-Q[14-25/1]-LB[10-125/0.5]
KZFC30-[100-500/0.5]-T[10,​20,​30,​40,​50]-P[25-33/1]-LA[15-150/0.5]-Q[20-29/1]-LB[15-150/0.5]
KZFC35-[100-500/0.5]-T[10,​20,​30,​40,​50]-P[28-38/1]-LA[15-150/0.5]-Q[20-34/1]-LB[15-150/0.5]
KZFC40-[200-500/0.5]-T[10,​20,​30,​40,​50]-P[35-47/1]-LA[20-150/0.5]-Q[20-39/1]-LB[20-150/0.5]
KZFC45-[200-500/0.5]-T[10,​20,​30,​40,​50]-P[35-48/1]-LA[20-150/0.5]-Q[20-44/1]-LB[20-150/0.5]
KZFF8-[50-219/0.5]-T[5,​10,​15,​20]-P[6-9/1]-LA[4-40/0.5]-Q[5-7/1]-LB[4-40/0.5]
KZFF10-[50-300/0.5]-T[5,​10,​15,​20]-P[8-12/1]-LA[5-50/0.5]-Q[7-9/1]-LB[5-50/0.5]
KZFF12-[50-300/0.5]-T[5,​10,​15,​20]-P[10-13/1]-LA[5-60/0.5]-Q[7-11/1]-LB[5-60/0.5]
KZFF12A-[50-300/0.5]-T[10,​15,​20,​25]-P[12-18/1]-LA[5-60/0.5]-Q[7-11/1]-LB[5-60/0.5]
KZFF15-[100-400/0.5]-T[10,​15,​20,​25]-P[12-18/1]-LA[5-75/0.5]-Q[10-14/1]-LB[5-75/0.5]
KZFF17-[100-400/0.5]-T[10,​15,​20,​25]-P[14-18/1]-LA[5-100/0.5]-Q[10-16/1]-LB[5-100/0.5]
KZFF17A-[100-400/0.5]-T[10,​15,​20,​25]-P[14-20/1]-LA[5-100/0.5]-Q[10-16/1]-LB[5-100/0.5]
KZFF20-[100-400/0.5]-T[10,​15,​20,​25]-P[17-23/1]-LA[5-100/0.5]-Q[14-19/1]-LB[5-100/0.5]
KZFF25-[100-500/0.5]-T[10,​20,​30,​40,​50]-P[20-28/1]-LA[10-125/0.5]-Q[14-24/1]-LB[10-125/0.5]
KZFF30-[100-500/0.5]-T[10,​20,​30,​40,​50]-P[25-33/1]-LA[15-150/0.5]-Q[20-29/1]-LB[15-150/0.5]
KZFF35-[100-500/0.5]-T[10,​20,​30,​40,​50]-P[28-38/1]-LA[15-150/0.5]-Q[20-34/1]-LB[15-150/0.5]
KZFF40-[200-500/0.5]-T[10,​20,​30,​40,​50]-P[35-47/1]-LA[20-150/0.5]-Q[20-39/1]-LB[20-150/0.5]
KZFF45-[200-500/0.5]-T[10,​20,​30,​40,​50]-P[35-48/1]-LA[20-150/0.5]-Q[20-44/1]-LB[20-150/0.5]
KZFN8-[50-219/0.5]-T[5,​10,​15,​20]-P[6-9/1]-LA[4-40/0.5]-Q[5-7/1]-LB[4-40/0.5]
KZFN10-[50-300/0.5]-T[5,​10,​15,​20]-P[8-12/1]-LA[5-50/0.5]-Q[7-9/1]-LB[5-50/0.5]
KZFN12-[50-300/0.5]-T[5,​10,​15,​20]-P[10-13/1]-LA[5-60/0.5]-Q[7-11/1]-LB[5-60/0.5]
KZFN12A-[50-300/0.5]-T[10,​15,​20,​25]-P[12-18/1]-LA[5-60/0.5]-Q[7-11/1]-LB[5-60/0.5]
KZFN15-[100-400/0.5]-T[10,​15,​20,​25]-P[12-18/1]-LA[5-75/0.5]-Q[10-14/1]-LB[5-75/0.5]
KZFN17-[100-400/0.5]-T[10,​15,​20,​25]-P[14-18/1]-LA[5-100/0.5]-Q[10-16/1]-LB[5-100/0.5]
KZFN17A-[100-400/0.5]-T[10,​15,​20,​25]-P[14-20/1]-LA[5-100/0.5]-Q[10-16/1]-LB[5-100/0.5]
KZFN20-[100-400/0.5]-T[10,​15,​20,​25]-P[17-23/1]-LA[5-100/0.5]-Q[14-19/1]-LB[5-100/0.5]
KZFN25-[100-500/0.5]-T[10,​20,​30,​40,​50]-P[20-28/1]-LA[10-125/0.5]-Q[14-24/1]-LB[10-125/0.5]
KZFN30-[100-500/0.5]-T[10,​20,​30,​40,​50]-P[25-33/1]-LA[15-150/0.5]-Q[20-29/1]-LB[15-150/0.5]
KZFN35-[100-500/0.5]-T[10,​20,​30,​40,​50]-P[28-38/1]-LA[15-150/0.5]-Q[20-34/1]-LB[15-150/0.5]
KZFN40-[200-500/0.5]-T[10,​20,​30,​40,​50]-P[35-47/1]-LA[20-150/0.5]-Q[20-39/1]-LB[20-150/0.5]
KZFN45-[200-500/0.5]-T[10,​20,​30,​40,​50]-P[35-48/1]-LA[20-150/0.5]-Q[20-44/1]-LB[20-150/0.5]
KZFP8-[50-219/0.5]-T[5,​10,​15,​20]-P[6-9/1]-LA[4-40/0.5]-Q[5-7/1]-LB[4-40/0.5]
KZFP10-[50-300/0.5]-T[5,​10,​15,​20]-P[8-12/1]-LA[5-50/0.5]-Q[7-9/1]-LB[5-50/0.5]
KZFP12-[50-300/0.5]-T[5,​10,​15,​20]-P[10-13/1]-LA[5-60/0.5]-Q[7-11/1]-LB[5-60/0.5]
KZFP12A-[50-300/0.5]-T[10,​15,​20,​25]-P[12-18/1]-LA[5-60/0.5]-Q[7-11/1]-LB[5-60/0.5]
KZFP15-[100-400/0.5]-T[10,​15,​20,​25]-P[12-18/1]-LA[5-75/0.5]-Q[10-14/1]-LB[5-75/0.5]
KZFP17-[100-400/0.5]-T[10,​15,​20,​25]-P[14-18/1]-LA[5-100/0.5]-Q[10-16/1]-LB[5-100/0.5]
KZFP17A-[100-400/0.5]-T[10,​15,​20,​25]-P[14-20/1]-LA[5-100/0.5]-Q[10-16/1]-LB[5-100/0.5]
KZFP20-[100-400/0.5]-T[10,​15,​20,​25]-P[17-23/1]-LA[5-100/0.5]-Q[14-19/1]-LB[5-100/0.5]
KZFP25-[100-500/0.5]-T[10,​20,​30,​40,​50]-P[20-28/1]-LA[10-125/0.5]-Q[14-24/1]-LB[10-125/0.5]
KZFP30-[100-500/0.5]-T[10,​20,​30,​40,​50]-P[25-33/1]-LA[15-150/0.5]-Q[20-29/1]-LB[15-150/0.5]
KZFP35-[100-500/0.5]-T[10,​20,​30,​40,​50]-P[28-38/1]-LA[15-150/0.5]-Q[20-34/1]-LB[15-150/0.5]
KZFP40-[200-500/0.5]-T[10,​20,​30,​40,​50]-P[35-47/1]-LA[20-150/0.5]-Q[20-39/1]-LB[20-150/0.5]
KZFP45-[200-500/0.5]-T[10,​20,​30,​40,​50]-P[35-48/1]-LA[20-150/0.5]-Q[20-44/1]-LB[20-150/0.5]
KZFS8-[50-219/0.5]-T[5,​10,​15,​20]-P[6-9/1]-LA[4-40/0.5]-Q[5-7/1]-LB[4-40/0.5]
KZFS10-[50-300/0.5]-T[5,​10,​15,​20]-P[8-12/1]-LA[5-50/0.5]-Q[7-9/1]-LB[5-50/0.5]
KZFS12-[50-300/0.5]-T[5,​10,​15,​20]-P[10-13/1]-LA[5-60/0.5]-Q[7-11/1]-LB[5-60/0.5]
KZFS12A-[50-300/0.5]-T[10,​15,​20,​25]-P[12-18/1]-LA[5-60/0.5]-Q[7-11/1]-LB[5-60/0.5]
KZFS15-[100-400/0.5]-T[10,​15,​20,​25]-P[12-18/1]-LA[5-75/0.5]-Q[10-14/1]-LB[5-75/0.5]
KZFS17-[100-400/0.5]-T[10,​15,​20,​25]-P[14-18/1]-LA[5-100/0.5]-Q[10-16/1]-LB[5-100/0.5]
KZFS17A-[100-400/0.5]-T[10,​15,​20,​25]-P[14-20/1]-LA[5-100/0.5]-Q[10-16/1]-LB[5-100/0.5]
KZFS20-[100-400/0.5]-T[10,​15,​20,​25]-P[17-23/1]-LA[5-100/0.5]-Q[14-19/1]-LB[5-100/0.5]
Part Number
Standard Unit Price
Minimum order quantityVolume Discount
Standard
Shipping Days
?
RoHSMaterial Hardness Surface Treatment Shaft Dia. D
(mm) 		Ds
(Ø) 		L
(mm) 		LA
(mm) 		LB
(mm) 		P
(mm) 		Q
(mm) 		T
(mm)

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide81050 ～ 2194 ～ 404 ～ 406 ～ 95 ～ 75 ～ 20

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide101350 ～ 3005 ～ 505 ～ 508 ～ 127 ～ 95 ～ 20

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide121450 ～ 3005 ～ 605 ～ 6010 ～ 137 ～ 115 ～ 20

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide12A1650 ～ 3005 ～ 605 ～ 6012 ～ 187 ～ 1110 ～ 25

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide1518100 ～ 4005 ～ 755 ～ 7512 ～ 1810 ～ 1410 ～ 25

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide1719100 ～ 4005 ～ 1005 ～ 10014 ～ 1810 ～ 1610 ～ 25

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide17A21100 ～ 4005 ～ 1005 ～ 10014 ～ 2010 ～ 1610 ～ 25

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide2024100 ～ 4005 ～ 1005 ～ 10017 ～ 2314 ～ 1910 ～ 25

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide2529100 ～ 50010 ～ 12510 ～ 12520 ～ 2814 ～ 2510 ～ 50

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide3034100 ～ 50015 ～ 15015 ～ 15025 ～ 3320 ～ 2910 ～ 50

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide3539100 ～ 50015 ～ 15015 ～ 15028 ～ 3820 ～ 3410 ～ 50

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide4048200 ～ 50020 ～ 15020 ～ 15035 ～ 4720 ～ 3910 ～ 50

-

1 16 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Black Oxide4549200 ～ 50020 ～ 15020 ～ 15035 ～ 4820 ～ 4410 ～ 50

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment81050 ～ 2194 ～ 404 ～ 406 ～ 95 ～ 75 ～ 20

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment101350 ～ 3005 ～ 505 ～ 508 ～ 127 ～ 95 ～ 20

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment121450 ～ 3005 ～ 605 ～ 6010 ～ 137 ～ 115 ～ 20

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment12A1650 ～ 3005 ～ 605 ～ 6012 ～ 187 ～ 1110 ～ 25

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment1518100 ～ 4005 ～ 755 ～ 7512 ～ 1810 ～ 1410 ～ 25

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment1719100 ～ 4005 ～ 1005 ～ 10014 ～ 1810 ～ 1610 ～ 25

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment17A21100 ～ 4005 ～ 1005 ～ 10014 ～ 2010 ～ 1610 ～ 25

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment2024100 ～ 4005 ～ 1005 ～ 10017 ～ 2314 ～ 1910 ～ 25

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment2529100 ～ 50010 ～ 12510 ～ 12520 ～ 2814 ～ 2410 ～ 50

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment3034100 ～ 50015 ～ 15015 ～ 15025 ～ 3320 ～ 2910 ～ 50

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment3539100 ～ 50015 ～ 15015 ～ 15028 ～ 3820 ～ 3410 ～ 50

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment4048200 ～ 50020 ～ 15020 ～ 15035 ～ 4720 ～ 3910 ～ 50

-

1 18 Days 10EN 1.1191 Equiv.-No Surface Treatment4549200 ～ 50020 ～ 15020 ～ 15035 ～ 4820 ～ 4410 ～ 50

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment81050 ～ 2194 ～ 404 ～ 406 ～ 95 ～ 75 ～ 20

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment101350 ～ 3005 ～ 505 ～ 508 ～ 127 ～ 95 ～ 20

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment121450 ～ 3005 ～ 605 ～ 6010 ～ 137 ～ 115 ～ 20

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment12A1650 ～ 3005 ～ 605 ～ 6012 ～ 187 ～ 1110 ～ 25

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment1518100 ～ 4005 ～ 755 ～ 7512 ～ 1810 ～ 1410 ～ 25

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment1719100 ～ 4005 ～ 1005 ～ 10014 ～ 1810 ～ 1610 ～ 25

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment17A21100 ～ 4005 ～ 1005 ～ 10014 ～ 2010 ～ 1610 ～ 25

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment2024100 ～ 4005 ～ 1005 ～ 10017 ～ 2314 ～ 1910 ～ 25

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment2529100 ～ 50010 ～ 12510 ～ 12520 ～ 2814 ～ 2410 ～ 50

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment3034100 ～ 50015 ～ 15015 ～ 15025 ～ 3320 ～ 2910 ～ 50

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment3539100 ～ 50015 ～ 15015 ～ 15028 ～ 3820 ～ 3410 ～ 50

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment4048200 ～ 50020 ～ 15020 ～ 15035 ～ 4720 ～ 3910 ～ 50

-

1 16 Days 10EN 1.1191 Equiv.No HardenedNo Surface Treatment4549200 ～ 50020 ～ 15020 ～ 15035 ～ 4820 ～ 4410 ～ 50

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating81050 ～ 2194 ～ 404 ～ 406 ～ 95 ～ 75 ～ 20

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating101350 ～ 3005 ～ 505 ～ 508 ～ 127 ～ 95 ～ 20

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating121450 ～ 3005 ～ 605 ～ 6010 ～ 137 ～ 115 ～ 20

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating12A1650 ～ 3005 ～ 605 ～ 6012 ～ 187 ～ 1110 ～ 25

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating1518100 ～ 4005 ～ 755 ～ 7512 ～ 1810 ～ 1410 ～ 25

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating1719100 ～ 4005 ～ 1005 ～ 10014 ～ 1810 ～ 1610 ～ 25

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating17A21100 ～ 4005 ～ 1005 ～ 10014 ～ 2010 ～ 1610 ～ 25

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating2024100 ～ 4005 ～ 1005 ～ 10017 ～ 2314 ～ 1910 ～ 25

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating2529100 ～ 50010 ～ 12510 ～ 12520 ～ 2814 ～ 2410 ～ 50

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating3034100 ～ 50015 ～ 15015 ～ 15025 ～ 3320 ～ 2910 ～ 50

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating3539100 ～ 50015 ～ 15015 ～ 15028 ～ 3820 ～ 3410 ～ 50

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating4048200 ～ 50020 ～ 15020 ～ 15035 ～ 4720 ～ 3910 ～ 50

-

1 18 Days 10EN 1.1191 Equiv.No Hardened[Surface Treatment Provided] Electroless Nickel Plating4549200 ～ 50020 ～ 15020 ～ 15035 ～ 4820 ～ 4410 ～ 50

-

1 18 Days 10EN 1.4301 Equiv.No HardenedNo Surface Treatment81050 ～ 2194 ～ 404 ～ 406 ～ 95 ～ 75 ～ 20

-

1 18 Days 10EN 1.4301 Equiv.No HardenedNo Surface Treatment101350 ～ 3005 ～ 505 ～ 508 ～ 127 ～ 95 ～ 20

-

1 18 Days 10EN 1.4301 Equiv.No HardenedNo Surface Treatment121450 ～ 3005 ～ 605 ～ 6010 ～ 137 ～ 115 ～ 20

-

1 18 Days 10EN 1.4301 Equiv.No HardenedNo Surface Treatment12A1650 ～ 3005 ～ 605 ～ 6012 ～ 187 ～ 1110 ～ 25

-

1 18 Days 10EN 1.4301 Equiv.No HardenedNo Surface Treatment1518100 ～ 4005 ～ 755 ～ 7512 ～ 1810 ～ 1410 ～ 25

-

1 18 Days 10EN 1.4301 Equiv.No HardenedNo Surface Treatment1719100 ～ 4005 ～ 1005 ～ 10014 ～ 1810 ～ 1610 ～ 25

-

1 18 Days 10EN 1.4301 Equiv.No HardenedNo Surface Treatment17A21100 ～ 4005 ～ 1005 ～ 10014 ～ 2010 ～ 1610 ～ 25

-

1 18 Days 10EN 1.4301 Equiv.No HardenedNo Surface Treatment2024100 ～ 4005 ～ 1005 ～ 10017 ～ 2314 ～ 1910 ～ 25

Loading...

  1. 1
  2. 2
  3. Next >>

Specifications/Overview

■Selection of Driving Shaft
In selecting a driving shaft, select the basic shape and size from the specification table, then select necessary alterations such as thread machining, keyway addition etc.

 

[Selection Example of Part Number]
·Alteration Selection: Two Threaded Ends (Fine Thread, Precision Grade), Two keyways


 

Driving Shaft - One End Stepped Shoulder Type: Related Image

[App. Example]

Driving Shaft - One End Stepped Shoulder Type: Related Image

 

Basic information

Basic Shape One End Stepped with Shoulder Shaft Tolerance h6

Configure

Clear all

65Suggestion of an applicable part number.

View Part Numbers

Some specification is not specified yet.
The part number is completed.

Basic Attributes

  • Material

    • EN 1.1191 Equiv.
    • EN 1.4301 Equiv.

    Clear

  • Hardness

    • No Hardened

    Clear

  • Surface Treatment

    • No Surface Treatment
    • Surface Treatment Provided
      • Black Oxide
      • Electroless Nickel Plating

    Clear

  • Shaft Dia. D(mm)

    • 8
    • 10
    • 12
    • 12A
    • 15
    • 17
    • 17A
    • 20
    • 25
    • 30
    • 35
    • 40
    • 45

    Clear

  • Ds(Ø)

    • 10
    • 13
    • 14
    • 16
    • 18
    • 19
    • 21
    • 24
    • 29
    • 34
    • 39
    • 48
    • 49

    Clear

  • L(mm)

     [50-500/0.5mm Unit(s)]

    Clear

  • LA(mm)

     [4-150/0.5mm Unit(s)]

    Clear

  • LB(mm)

     [4-150/0.5mm Unit(s)]

    Clear

  • P(mm)

     [6-48/1mm Unit(s)]

    Clear

  • Q(mm)

     [5-44/1mm Unit(s)]

    Clear

  • T(mm)

    • 5
    • 10
    • 15
    • 20
    • 25
    • 30
    • 40
    • 50

    Clear

  • Type

    • KZFC
    • KZFF
    • KZFN
    • KZFP
    • KZFS

    Clear

  • Filter by CAD data type

    • 2D
    • 3D

    Clear

Filter by standard shipping days

    • All
    • 16 Days or Less
    • 18 Days or Less

    Reset

Optional Attributes

Complementary Products

Tech Support

Technical Support
Tel：+49 69 668173-0 / FAX：+49 69 668173-360
Technical Inquiry

Payment Method

  • Payment on account
  • Pre Payment
  • PayPal

On-Demand Manufacturing

Change View

Certificates

  • ISO-9001
  • ISO-14001
  • AEO Certification
  • RoHS
  • REACH

MISUMI worldwide

Social Media

Legal notice

Copyright © MISUMI Corporation All Rights Reserved.