Stainless Steel Belts
Click on this image to zoom in.
Click on this image to zoom in.
Part Number
Once your search is narrowed to one product,
the corresponding part number is displayed here.
- Drawing / Specifications
- 3D Preview 3D preview is available after complete configuration
- Part Numbers
- More Information
- Catalog
Dimensional Drawing
[ ! ]Endless jointing is applied before the product is shipped.
[ ! ]The circumference of the belt is the length of the back side of the belt (inner diameter circumference).
[ ! ]There is no fixed direction in which the belt travels.
| Type | [M] Material | Thickness mm | Specific Gravity | Allowable Tension kg/cm | Min. Pulley Dia. ⌀mm | Continuous Use Temperature °C | Electrical Resistance of Surface Ω | Friction Coefficient (Ref. Against Polished Steel) | [H]Surface Hardness HV | Young's Modulus kgf/mm2 | Heat Expansion Coefficient × 10−6/°C |
| STHBLT | EN 1.4301 Equiv. | 0.1 | 0.8 | 4 | 50 | −80 to 110 | 0.2 | 0.2 | 370 or over | 19700 | 17.3 |
| 0.15 | 1.2 | 6 | 75 | −80 to 120 | 0.3 | ||||||
| 0.2 | 1.6 | 8 | 100 | −80 to 130 | 0.5 |
Specification Table
| Part Number | — | Belt Width (mm) | — | Belt Length L (m) | ||
| Type | Belt Thickness | |||||
| STHBLT | 0.15 | — | 25 | — | 2.24 | |
| Part Number | Belt Width W (mm) 1 mm Increments | Belt Length L (m) 0.01 m Increments | |
| Type | Belt Thickness T (mm) | ||
| STHBLT | 0.1 0.15 0.2 | 10 to 20 | 0.50 to 10.00 |
| 21 to 30 | 0.80 to 10.00 | ||
| 31 to 40 | |||
| 41 to 50 | |||
| 51 to 60 | |||
| 61 to 70 | |||
| 71 to 80 | |||
| 81 to 90 | |||
| 91 to 100 | |||
| 101 to 120 | |||
| 121 to 140 | |||
| 141 to 150 | |||
| Width (W) | ±0.1 |
| Thickness (t) | ±10% to belt thickness |
| Circumference Length | ±1 mm/m |
[ ! ]Belts with 0.1 and 0.15 thickness are not suitable for accumulating transfer applications.
[ ! ]Avoid causing impacts in through-thickness direction as it is very thin.
[ ! ]The belt life will be reduced if dented.
[ ! ]When loading items on the belt, use sliding chutes to avoid shock loads.
[ ! ]Do not continue to use with foreign matter stuck between the belt and belt support / workpiece guide.
[ ! ]The product surfaces coming in contact with the belt should be softer than the belt.
[ ! ]Use dedicated pulleys and idlers.
[ ! ]Belts cannot be tensioned from the back side.
[ ! ]If this product is used under the minimum pulley diameters, a slip may occur between the belt and the pulley.
[!]The life of a belt is difficult to calculate, so if the belt appears damaged or worn on the surface, it should be replaced.
Part Number:
- In order to open the 3D preview, the part number must be fixed.
3D preview is not available, because the part number has not yet been determined.
| Part Number |
Standard Unit Price
| Minimum order quantity | Volume Discount | RoHS | Belt Width W (mm) | Thickness (mm) | Unit Mass (kg/m²) | Allowable Tension (N/mm) | Min. Pulley Dia. (mm) | Circumference Length (m) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
- | 1 | 12 Days | 10 | 10 | 0.1 | 0.8 | 4 | 50 | 0.5 ～ 10 | ||
- | 1 | 12 Days | 10 | 11 | 0.1 | 0.8 | 4 | 50 | 0.5 ～ 10 | ||
- | 1 | 12 Days | 10 | 12 | 0.1 | 0.8 | 4 | 50 | 0.5 ～ 10 | ||
- | 1 | 12 Days | 10 | 13 | 0.1 | 0.8 | 4 | 50 | 0.5 ～ 10 | ||
- | 1 | 12 Days | 10 | 14 | 0.1 | 0.8 | 4 | 50 | 0.5 ～ 10 | ||
- | 1 | 12 Days | 10 | 15 | 0.1 | 0.8 | 4 | 50 | 0.5 ～ 10 | ||
- | 1 | 12 Days | 10 | 16 | 0.1 | 0.8 | 4 | 50 | 0.5 ～ 10 | ||
- | 1 | 12 Days | 10 | 17 | 0.1 | 0.8 | 4 | 50 | 0.5 ～ 10 | ||
- | 1 | 12 Days | 10 | 18 | 0.1 | 0.8 | 4 | 50 | 0.5 ～ 10 | ||
- | 1 | 12 Days | 10 | 19 | 0.1 | 0.8 | 4 | 50 | 0.5 ～ 10 | ||
- | 1 | 12 Days | 10 | 20 | 0.1 | 0.8 | 4 | 50 | 0.5 ～ 10 | ||
- | 1 | 12 Days | 10 | 21 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 22 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 23 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 24 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 25 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 26 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 27 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 28 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 29 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 30 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 31 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 32 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 33 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 34 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 35 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 36 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 37 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 38 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 39 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 40 | 0.1 | 0.8 | 4 | 50 | 0.66 ～ 10 | ||
- | 1 | 12 Days | 10 | 41 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 42 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 43 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 44 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 45 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 46 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 47 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 48 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 49 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 50 | 0.1 | 0.8 | 4 | 50 | 0.66 ～ 10 | ||
- | 1 | 12 Days | 10 | 51 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 52 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 53 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 54 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 55 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 56 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 57 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 58 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 59 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 60 | 0.1 | 0.8 | 4 | 50 | 0.66 ～ 10 | ||
- | 1 | 12 Days | 10 | 61 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 62 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 63 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 64 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 65 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 66 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 67 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 68 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 | ||
- | 1 | 12 Days | 10 | 69 | 0.1 | 0.8 | 4 | 50 | 0.8 ～ 10 |
Loading...
Specifications / Overview
| Food | Stainless Steel Belt |
| STHBLT | |
| Yeast | ○ |
| Tea Leaf | ○ |
| Olive Oil | ○ |
| Fruit | ○ |
| Cashew Nuts | ○ |
| Cream | ○ |
| Spice | ○ |
| Grain | ○ |
| Coffee Beans | ○ |
| Flour | ○ |
| Rice Grain | ○ |
| Fish | ○ |
| Sugar | ○ |
| Salt | ○ |
| Salt Water | ○ |
| Fat | ○ |
| Cooking Oil | ○ |
| Syrup | ○ |
| Soy Sauce | ○ |
| Vinegar | ○ |
| Sauce | ○ |
| Molasses | ○ |
| Meat | ○ |
| Butter | ○ |
| Bread | ○ |
| Peanut Oil | ○ |
| Beer | ○ |
| Margarine | ○ |
| Mayonnaise | ○ |
| Water | ○ |
| Lard | ○ |
| Chemical Name | Stainless Steel Belt |
| STHBLT | |
| Isopropyl Alcohol | ○ |
| Ethanol | ○ |
| Potassium Chloride | ○ |
| Calcium Chloride | ○ |
| Hydrochloric Acid (Gas) | × |
| Hydrochloric Acid (5% or less) | × |
| Hydrochloric Acid (5 to 36%) | × |
| Sodium Hydroxide | ○ |
| Sodium Hydroxide Liquid (50%) | ○ |
| Volatile Oil | ○ |
| Strong Alkali | ○ |
| Strong Acid | × |
| Light Oil | ○ |
| Ethyl Acetate | △ |
| Sodium Hypochlorite (Undiluted Solution) | × |
| Sodium Hypochlorite (600 ppm) | × |
| Weak Alkali | ○ |
| Weak Acid | ○ |
| Soap | ○ |
| Machining Oil | ○ |
| Diesel Oil | ○ |
| Toluene | ○ |
| Naphthalene | ○ |
| Paraffin Oil | ○ |
| Phenol | ○ |
| Antirust Oil | ○ |
| Machine Oil | ○ |
| Methanol | ○ |
| Sulfuric Acid (10%) | × |
| Sulfuric Acid (50%) | × |
| Sulfuric Acid (70%) | × |
| Sulfuric Acid (98%) | × |
App. Example
Basic information
| Belt Specification | General Purpose | Surface Cover Color | Silver | Surface Cover Material | EN 1.4301 Equiv. |
|---|---|---|---|---|---|
| Surface Cover Shape | Flat | Friction Coefficient (Ref. Against Polished Steel) Front | 0.2 | Friction Coefficient (Ref. Against Polished Steel) Back | 0.2 |
| Knife Edge(mm) | Not Provided |
Configure
Basic Attributes
-
Belt Width W(mm)
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
- 44
- 45
- 46
- 47
- 48
- 49
- 50
- 51
- 52
- 53
- 54
- 55
- 56
- 57
- 58
- 59
- 60
- 61
- 62
- 63
- 64
- 65
- 66
- 67
- 68
- 69
- 70
- 71
- 72
- 73
- 74
- 75
- 76
- 77
- 78
- 79
- 80
- 81
- 82
- 83
- 84
- 85
- 86
- 87
- 88
- 89
- 90
- 91
- 92
- 93
- 94
- 95
- 96
- 97
- 98
- 99
- 100
- 101
- 102
- 103
- 104
- 105
- 106
- 107
- 108
- 109
- 110
- 111
- 112
- 113
- 114
- 115
- 116
- 117
- 118
- 119
- 120
- 121
- 122
- 123
- 124
- 125
- 126
- 127
- 128
- 129
- 130
- 131
- 132
- 133
- 134
- 135
- 136
- 137
- 138
- 139
- 140
- 141
- 142
- 143
- 144
- 145
- 146
- 147
- 148
- 149
- 150
-
Thickness(mm)
-
Unit Mass(kg/m²)
-
Allowable Tension(N/mm)
-
Min. Pulley Dia.(mm)
-
Circumference Length(m)
-
Type
- STHBLT
-
Filter by CAD data type
- 2D
- 3D
Filter by standard shipping days
-
- All
- 12 Days or Less
Optional Attributes
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Complementary Products
Tech Support
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.