Sheet Metal Mounting Plate / Bracket - Custom Dimensions Type - JTHBS
- Order quantities extended (D-JIT)
Part Number
Once your search is narrowed to one product,
the corresponding part number is displayed here.
- Drawing / Specifications
- 3D Preview 3D preview is available after complete configuration
- Part Numbers
- Catalog
- Technical Information
Dimensional Drawing
JTHBS
[ ! ]Orientation of Slotted Holes can be changed. Please be careful about the dimensions. (Refer to the "Alterations" section.)
[ ! ]Green colored parameters can be omitted. If the parameter setting is omitted, the holes will be evenly distributed about the center.
[ ! ]For details on specifications and machining limits, see >> here
[ ! ]Green colored parameters can be omitted. If the parameter setting is omitted, the holes will be evenly distributed about the center.
[ ! ]For details on specifications and machining limits, see >> here
■Hole Type Selection Chart
| Hole Type | Bolt Hole | Through Hole with Tolerance |
| Code | N | D |
| Shape Diagram | [ ! ]  |  |
| [ ! ]For the d dimensions, refer to the "N Machining Dimensions" section below the Specifications Table |
| Part Number | [ M ]Material | [ S ]Surface Treatment | ||
| Type | Material Symbol | |||
| JTHBS | SP | T0.8~3.2 T4.5~6.0 | : EN 1.0330 Equiv. : EN 1.0320 Equiv. (hot coiled) | − |
| SPB | Black Oxide | |||
| SPU | Trivalent Chromate (Clear) | |||
| SPK | Trivalent Chromate (Black) | |||
| AM | EN AW−5052 Equiv. | − | ||
| AMW | Anodize (Clear) | |||
| AMB | Anodize (Black) | |||
| SUD | EN 1.4301 Equiv. (Passivated 2B) | − | ||
Specification Table
| Part Number | － | A | － | B | － | T | － | X | － | Y | － | G | － | Hole Specification (1) Code / Nominal Dia. | － | K | － | L | － | S | － | D | ||
| Type | － | Material Symbol | ||||||||||||||||||||||
| JTHBS | － | SP | － | A120 | － | B80 | － | T2.3 | － | X20 | － | Y20 | － | G40 | － | N8 | － | K20 | － | L70 | － | S40 | － | D30 |
| Part Number | 1 mm Increments | Selection | X | Y | G | Hole Specification (1) | K | L | S | D | ||||
| Type | Material Symbol | A | B | T | Code / Specify Method | |||||||||
| JTHBS | SP SPB SPU SPK | 15 ～ 300 | 15 ～ 300 | 0.8 ・ 1.0 ・ 1.2 ・ 1.6 ・ 2.3 3.2 ・ 4.5 ・ 6.0 | 0.1 mm Increments | N (Bolt Hole) 0・3・4・5 6・8・10 (Select) [ ! ] | 0.1 mm Increments [ ! ]K≤N×10 | 3～30 (0.5 mm Increments) | ||||||
| AM AMW AMB | 1.0 ・ 1.5 ・ 2.0 ・ 3.0 ・ 4.0 ・ 5.0 | |||||||||||||
| SUD | 0.8 ・ 1.0 ・1.2 ・ 1.5 ・ 2.0 3.0 ・ 4.0 ・ 5.0 ・6.0 | |||||||||||||
| [ ! ]If the specified hole location is close to the edges, the hole may be deformed but will be machined as specified if within machining limits. | ||||||||||||||
[ ! ]N Machining Dimension Table
| N Specified Value | Through Hole Diameter (d) |
| 0 | (No Hole) |
| 3 | 3.5 |
| 4 | 4.5 |
| 5 | 5.5 |
| 6 | 6.5 |
| 8 | 9 |
| 10 | 11 |
Alterations
Alteration | Slotted Hole Angle Change | Corner cut | ||||
 |  | |||||
Code | RC | CC | ||||
Spec. | Slotted holes are changed as shown above. [!] Note the dimensional relationship
(Example) ... -RC | CC = 1 mm Increments 1 ≤ CC ≤ 10
(Example) ... -CC5 | ||||
■Specifications, Machining Limits
[ ! ]1．See the figure below for tolerances
[Standard Machined Dimension Tolerances]
*For sheet metals, Class B Tolerance stipulated in JIS B 0408, General dimensional tolerances for parts formed
by press working from sheet metal is used.:
[Standard Machined Dimension Tolerances]
| Product | Dimension Range (A, B Dimension) | 6 or less | Over 6, and 30 or less | Over 30, and 120 or less | Over 120, and 400 or less |
| Sheet Metal (No Bending) | Tolerance（a・b） | ±0.1 | ±0.2 | ±0.3 | ±0.5 |
by press working from sheet metal is used.:
[ ! ]2．Burr height 0.1 or less
[ ! ]3．In case of the thin plates, the tap ridges may be crushed, so please be careful when tightening.
[ ! ]The hole may be deformed if specified at the limit value shown above.
[ ! ]3．In case of the thin plates, the tap ridges may be crushed, so please be careful when tightening.
[ ! ]4．Slotted holes may be shaped as shown below depending on dimensions.
(The function as a mounting hole is not affected.)
[ ! ]5. There are machining limits for thickness between hole and hole or between hole and end face. (Example: "b" on the drawing below)
| T | b | ||
| EN 1.0330 Equiv. EN 1.0320 Equiv. (hot coiled) | EN AW−5052 Equiv. | EN 1.4301 Equiv. | |
| 0.8 | ー | 0.8 | 1 |
| 1.0 | 1.0 | 1.0 | 1 |
| 1.2 | ー | 1.2 | 1 |
| 1.6 | 1.5 | 1.5 | 1 |
| 2.3 | 2.0 | 2.0 | 1.5 |
| 3.2 | 3.0 | 3.0 | 1.5 |
| 4.5 | 4.0 | 4.0 | 2 |
| ー | 5.0 | 5.0 | 2.5 |
| 6.0 | ー | 6.0 | 2.5 |
■Appearance per Material (Surface Treatment) and Machining Method
| None | Black Oxide | Trivalent Chromate (Clear) | Trivalent Chromate (Black) | |
| SP | SPB | SPU | SPK | |
| EN 1.0330 Equiv. T0.8～3.2 |  |  |  |  |
| EN 1.0320 Equiv. (hot coiled) T4.5～6.0 |  |  |  |  |
| EN 1.0038 Equiv. （Black） T9.0 |  |  |  |  |
| None | Anodize (Clear) | Anodize (Black) | |
| AM | AMW | AMB | |
| EN AW−5052 Equiv. |  |  |  |
| None | |
| SUD | |
| EN 1.4301 Equiv. (2B) T0.8～6.0 |  |
| EN 1.4301 Equiv. （No.1） T9.0 |  |
App. Example
Sensor mounting plate that requires height adjustment
Part Number:
- In order to open the 3D preview, the part number must be fixed.
3D preview is not available, because the part number has not yet been determined.
Loading...
| Part Number | Minimum order quantity | Volume Discount | RoHS | Material | Surface Treatment | A (mm) | B (mm) | T (mm) | |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 7 Days | 10 | EN AW-5052 Equiv. | Not Provided | 15 ～ 300 | 15 ～ 300 | 1.5 ～ 5 | ||
| 1 | 9 Days | 10 | EN AW-5052 Equiv. | Black Anodize | 15 ～ 300 | 15 ～ 300 | 1.5 ～ 5 | ||
| 1 | 9 Days | 10 | EN AW-5052 Equiv. | Clear Anodize | 15 ～ 300 | 15 ～ 300 | 1.5 ～ 5 | ||
| 1 | 7 Days | 10 | EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled)) | Not Provided | 15 ～ 300 | 15 ～ 300 | 1.6 ～ 6 | ||
| 1 | 9 Days | 10 | EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled)) | Black Oxide | 15 ～ 300 | 15 ～ 300 | 1.6 ～ 6 | ||
| 1 | 7 Days | 10 | EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled)) | Trivalent Chromate (Black) | 15 ～ 300 | 15 ～ 300 | 1.6 ～ 6 | ||
| 1 | 7 Days | 10 | EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled)) | Trivalent Chromate (White) | 15 ～ 300 | 15 ～ 300 | 1.6 ～ 6 | ||
| 1 | 7 Days | 10 | EN 1.4301 Equiv. (2B) | Not Provided | 15 ～ 300 | 15 ～ 300 | 1 ～ 5 |
Loading...
Basic information
| Type | Sheet Metal | Part Mounting Hole | Yes | Slotted Hole | Yes |
|---|---|---|---|---|---|
| Side Hole | N/A | Hole Position | Free Dimension | Number Of Holes | 3 |
| Type | Dimension Configurable Type | Type | JTHBS |
Configure
Basic Attributes
-
Material
- EN AW-5052 Equiv.
- EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled))
- EN 1.4301 Equiv. (2B)
-
Surface Treatment
- Black Anodize
- Black Oxide
- Clear Anodize
- Not Provided
- Trivalent Chromate (Black)
- Trivalent Chromate (White)
-
A(mm)
-
B(mm)
-
T(mm)
-
Type
- JTHBS-AM
- JTHBS-AMB
- JTHBS-AMW
- JTHBS-SP
- JTHBS-SPB
- JTHBS-SPK
- JTHBS-SPU
- JTHBS-SUD
-
Filter by CAD data type
- 2D
- 3D
Filter by standard shipping days
-
- All
- 7 Days or Less
- 9 Days or Less
Optional Attributes
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Tech Support
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.