Sheet Metal Mounting Plate / Bracket - Custom Dimensions Type - JTACS
- Order quantities extended (D-JIT)
Part Number
Once your search is narrowed to one product,
the corresponding part number is displayed here.
- Drawing / Specifications
- 3D Preview 3D preview is available after complete configuration
- Part Numbers
- Catalog
- Technical Information
Dimensional Drawing
| JTACS |
[!] Green colored parameters can be omitted. If the parameter setting is omitted, the holes will be evenly distributed about the center.
[!] For details on specifications and machining limits, see >>Here
■Hole Type Selection Chart
| Hole Type | Bolt Hole | Tapped Hole (Coarse) |
| Code | N・NA | M・MA |
| Shape Diagram |  [ ! ] [ ! ]For d dimension, see "N, NA Machining Dimension Table" |  |
| Part Number | [M] Material | [S] Surface Treatment | ||
| Type | Material Symbol | |||
| JTACS | SP | T0.8~3.2 T4.5~6.0 T9.0 | : EN 1.0330 Equiv. : EN 1.0320 Equiv. (hot coiled) : EN 1.0038 Equiv.(Black) | — |
| SPB | Black Oxide | |||
| SPU | Trivalent Chromate (Clear) | |||
| SPK | Trivalent Chromate (Black) | |||
| AM | EN AW−5052 Equiv. | — | ||
| AMW | Anodize (Clear) | |||
| AMB | Anodize (Black) | |||
| SUD | T0.8~6.0 T9.0 | : EN 1.4301 Equiv. (Passivated 2B) : EN 1.4301 Equiv.(No.1) | — | |
Specification Table
| Part Number | — | A | — | B | — | T | — | X | — | F | — | Y | — | G | — | Hole Specification (1) Code / Nominal Dia. | — | L | — | V | — | S | — | W | — | Hole Specification (2) Code / Nominal Dia. | ||
| Type | — | Material Symbol | ||||||||||||||||||||||||||
| JTACS | — | SP | — | A120 | — | B80 | — | T2.3 | — | X20 | — | F25 | — | Y20 | — | G40 | — | N8 | — | L80 | — | V25 | — | S20 | — | W40 | — | MA4 |
| Part Number | 1 mm Increments | Selection | X | F | Y | G | Hole Specification (1) | L | V | S | W | Hole Specification (2) | ||||||
| Type | Material Symbol | A | B | T | Code / Specify Method | Code / Specify Method | ||||||||||||
| JTACS | SP SPB SPU SPK | 15 ～ 300 | 15 ～ 300 | 0.8 ・ 1.0 ・ 1.2 ・ 1.6 ・ 2.3 3.2 ・ 4.5 ・ 6.0 ・ 9.0 | Configurable 0.1 mm Increments | N (Bolt Hole) 0・3・4・5 6・8・10 (Select) [ ! ] | M (Tapped Holes) 0・3・4・5 6・8・10 (Select) [ ! ] | Configurable 0.1 mm Increments | NA (Bolt Hole) 0・3・4・5 6・8・10 (Select) [ ! ] | MA | ||||||||
| AM AMW AMB | 1.0 ・ 1.5 ・ 2.0 ・ 3.0 ・ 4.0 ・ 5.0 | |||||||||||||||||
| SUD | 0.8 ・ 1.0 ・ 1.2 ・ 1.5 ・ 2.0 3.0 ・ 4.0 ・ 5.0 ・ 6.0 ・ 9.0 | |||||||||||||||||
| [ ! ] If the specified hole location is close to the edges, the hole may be deformed but will be machined as specified if within machining limits. | ||||||||||||||||||
[ ! ] N, NA machining dimensions
| N, NA Specified Value | Through Hole Dia. (d) |
| 0 | (No Hole) |
| 3 | 3.5 |
| 4 | 4.5 |
| 5 | 5.5 |
| 6 | 6.5 |
| 8 | 9 |
| 10 | 11 |
[ ! ] Hole Machining Table
[ ! ] T = 1.0 is not applicable for tapped holes to AM, AMW, or AMB
| T | N・NA(Bolt Hole) | M・MA(Tapped Holes) |
| 0.8 | 0・3・4・5・6・8・10 | 0 |
| 1.0、1.2 | 0・3 | |
| 1.5、1.6 | 0・3・4 | |
| 2.0、2.3 | 0・3・4・5・6 | |
| 3.0、3.2 | 0・3・4・5・6・8 | |
| 4.0～6.0 | 0・3・4・5・6・8・10 | |
| 9.0 | 0・5・6・8・10 | 0・5・6・8・10 |
Alteration
| Alteration | Corner cut | ||
 | |||
| Code | CC | ||
| Spec. | CC = 1 mm Increments 1 ≤ CC ≤ 10
(Example) ... -CC5 | ||
■Specifications, Machining Limits
[ ! ] 1．See the figure below for tolerances
[ ! ] 3. In case of the thin plates, the tap ridges may be crushed, so please be careful when tightening.
[ ! ] 4. When changing to a specification without holes, anodizing with T4 or more may cause a hang hole to be formed as shown in the figure below.
<Standard Machined Dimension Tolerances>
*For sheet metals, Class B Tolerance stipulated in JIS B 0408, General dimensional tolerances for parts formed
by press working from sheet metal is used.
[ ! ] 2. Burr height 0.1 or less.| Product | Dimension Range (A, B Dimension) | 6 or less | Over 6, and 30 or less | Over 30, and 120 or less | Over 120, and 400 or less |
| Sheet Metal (No Bending) | Tolerance（a・b） | ±0.1 | ±0.2 | ±0.3 | ±0.5 |
by press working from sheet metal is used.
[ ! ] 3. In case of the thin plates, the tap ridges may be crushed, so please be careful when tightening.
[ ! ] 4. When changing to a specification without holes, anodizing with T4 or more may cause a hang hole to be formed as shown in the figure below.
[ ! ] 5. There are machining limits for thickness between hole and hole or between hole and end face. (Example: "b" on the drawing below)
| T | b | ||
| EN 1.0330 Equiv. EN 1.0320 Equiv. (hot coiled) EN 1.0038 Equiv. | |||
| EN AW−5052 Equiv. | EN 1.4301 Equiv. | ||
| 0.8 | ー | 0.8 | 1 |
| 1.0 | 1.0 | 1.0 | 1 |
| 1.2 | ー | 1.2 | 1 |
| 1.6 | 1.5 | 1.5 | 1 |
| 2.3 | 2.0 | 2.0 | 1.5 |
| 3.2 | 3.0 | 3.0 | 1.5 |
| 4.5 | 4.0 | 4.0 | 2 |
| ー | 5.0 | 5.0 | 2.5 |
| 6.0 | ー | 6.0 | 2.5 |
| 9.0 | ー | 9.0 | 4 |
■Appearance per Material (Surface Treatment) and Machining Method
| None | Black Oxide | Trivalent Chromate (Clear) | Trivalent Chromate (Black) | |
| SP | SPB | SPU | SPK | |
| EN 1.0330 Equiv. T0.8～3.2 |  |  |  |  |
| EN 1.0320 Equiv. (hot coiled) T4.5～6.0 |  |  |  |  |
| EN 1.0038 Equiv. （Black） T9.0 |  |  |  |  |
| None | Anodize (Clear) | Anodize (Black) | |
| AM | AMW | AMB | |
| EN AW−5052 Equiv. |  |  |  |
| None | |
| SUD | |
| EN 1.4301 Equiv. (Passivated 2B) T0.8～6.0 |  |
| EN 1.4301 Equiv.（No.1） T9.0 | .gif)  |
Part Number:
- In order to open the 3D preview, the part number must be fixed.
3D preview is not available, because the part number has not yet been determined.
Loading...
| Part Number | Minimum order quantity | Volume Discount | RoHS | Material | Surface Treatment | A (mm) | B (mm) | T (mm) | |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 7 Days | 10 | EN AW-5052 Equiv. | Not Provided | 15 ～ 300 | 15 ～ 300 | 1.5 ～ 5 | ||
| 1 | 9 Days | 10 | EN AW-5052 Equiv. | Black Anodize | 15 ～ 300 | 15 ～ 300 | 1.5 ～ 5 | ||
| 1 | 9 Days | 10 | EN AW-5052 Equiv. | Clear Anodize | 15 ～ 300 | 15 ～ 300 | 1.5 ～ 5 | ||
| 1 | 7 Days | 10 | EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled)) | Not Provided | 15 ～ 300 | 15 ～ 300 | 1.6 ～ 6 | ||
| 1 | 9 Days | 10 | EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled)) | Black Oxide | 15 ～ 300 | 15 ～ 300 | 1.6 ～ 6 | ||
| 1 | 7 Days | 10 | EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled)) | Trivalent Chromate (Black) | 15 ～ 300 | 15 ～ 300 | 1.6 ～ 6 | ||
| 1 | 7 Days | 10 | EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled)) | Trivalent Chromate (White) | 15 ～ 300 | 15 ～ 300 | 1.6 ～ 6 | ||
| 1 | 7 Days | 10 | EN 1.4301 Equiv. (2B) | Not Provided | 15 ～ 300 | 15 ～ 300 | 1 ～ 5 |
Loading...
Basic information
| Type | Sheet Metal | Part Mounting Hole | N/A | Slotted Hole | N/A |
|---|---|---|---|---|---|
| Side Hole | N/A | Hole Position | Free Dimension | Number Of Holes | 8 |
| Type | Dimension Configurable Type | Type | JTACS |
Configure
Basic Attributes
-
Material
- EN AW-5052 Equiv.
- EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled))
- EN 1.4301 Equiv. (2B)
-
Surface Treatment
- Black Anodize
- Black Oxide
- Clear Anodize
- Not Provided
- Trivalent Chromate (Black)
- Trivalent Chromate (White)
-
A(mm)
-
B(mm)
-
T(mm)
-
Type
- JTACS-AM
- JTACS-AMB
- JTACS-AMW
- JTACS-SP
- JTACS-SPB
- JTACS-SPK
- JTACS-SPU
- JTACS-SUD
-
Filter by CAD data type
- 2D
- 3D
Filter by standard shipping days
-
- All
- 7 Days or Less
- 9 Days or Less
Optional Attributes
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Tech Support
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.