• Brands
  • Company
  • Contact
EN / UK
Type Code Seach | *NOT READY*
#CODE
Keyword suggestions
Part number suggestions
Discontinued Products

Sheet Metal Mounting Plate / Bracket -Z Bending Type- SWBAS

Sheet Metal Mounting Plate / Bracket -Z Bending Type- SWBAS

MISUMI

MISUMI

  • Order quantities extended (D-JIT)

Data sheet

Part Number

Once your search is narrowed to one product,
the corresponding part number is displayed here.

SWBAS
[ ! ]Green colored parameters can be omitted. If the parameter setting is omitted, the holes will be evenly distributed about the center.
[ ! ]For details on specifications and machining limits, see >> here
■Hole Type Selection Chart
Hole TypeBolt HoleTapped Hole (Coarse)
CodeN・NAM・MA
Shape Diagram

[ ! ]

[ ! ]For the d dimensions, refer to the "N, NA Machining Dimensions"
section below the Specifications Table

 
Part Number[ M ]Material[ S ]Surface Treatment
TypeMaterial Symbol
SWBASSPT0.8~3.2：EN 1.0330 Equiv.
T4.5~6.0：EN 1.0320 Equiv. (hot coiled)		−
SPBBlack Oxide
SPUTrivalent Chromate (Clear)
SPKTrivalent Chromate (Black)
AMEN AW−5052 Equiv.−
AMWAnodize (Clear)
AMBAnodize (Black)
SUDEN 1.4301 Equiv. (Passivated 2B)−

Specification Table

Part Number−A−B−T−H−J−X−Y−W−Hole Specification①
Code, Nominal		−F−S−G−Hole Specification②
Code, Nominal
   
Type－Material Symbol
SWBAS−SP−A80−B40−T2.3−H15−J37−X18−Y5−W30−N4−F44−S5−G30−NA5
Part Number1 mm IncrementsSelection1 mm IncrementsJXYWHole Specification①FSGHole Specification②
TypeMaterial SymbolABTHCode / Specify MethodCode / Specify Method
SWBASSP
SPB
SPU
SPK		20
～
200
[ ! ]		10
～
200
 		0.8 ・ 1.0 ・ 1.2 ・ 1.6
2.3 ・ 3.2 ・ 4.5 ・ 6.0 		10
～
100		0.1 mm Increments
N
(Bolt Hole)
0・3・4・5
6・8・10
（Selection）
[ ! ]
M
(Tapped Holes)
0・3・4・5
6・8・10
（Selection）
[ ! ]
0.1 mm Increments
NA
(Bolt Hole)
0・3・4・5
6・8・10
（Selection）
[ ! ]
MA
(Tapped Holes)
0・3・4・5
6・8・10
（Selection）
[ ! ]
AM
AMW
AMB		1.0 ・ 1.5 ・ 2.0 ・ 3.0
SUD0.8 ・ 1.0 ・ 1.2 ・ 1.5
2.0 ・ 3.0 ・ 4.0
[ ! ]When T ≥ 3.0, A ≥ 30
[ ! ]If the specified hole location is close to the edges, the hole may be deformed but will be machined as specified if within machining limits.
[ ! ]N・NA Machining Dimension Table
N・NA Specified ValueThrough Hole Diameter (d)
0(No Hole)
33.5
44.5
55.5
66.5
89
1011
[ ! ]Hole Machining Table
TN・NA (Bolt Hole)M・MA (Tapped Holes)
0.80・3・4・5・6・8・100
1.0、1.20・3
1.5、1.60・3・4
2.0、2.30・3・4・5・6
3.0、3.20・3・4・5・6・8
4.0～6.00・3・4・5・6・8・10
[ ! ]T = 1.0 is not applicable for tapped holes to AM, AMW, or AMB

 

Alterations

AlterationsCorner Cut Change (2 Corners)Corner Cut Change (4 corners)
CodeCCWCC
Spec.CC = 1 mm Increments　
[ ! ] 1 ≤ CC ≤ 10
Specifying Method
Add CC to the end of a Part Number.
Example: ... -CC10		WCC = 1 mm Increments　
[ ! ] 1 ≤ WCC ≤ 10
Specifying Method
Add WCC at the end of the type designation
Example: ... -WCC10

Specifications, Machining Limits

[ ! ] 1．See the figure below for tolerances

[Standard Machined Dimension Tolerances]
ProductDimension Range
(A, H dimension)		6 or lessOver 6, and
30 or less		Over 30, and
120 or less		Over 120, and
400 or less
Sheet Metal (Bent Products)Tolerance（a・h）±0.3±0.5±0.8±1.2
* Class B Tolerance stipulated in JIS B 0408, General dimensional tolerances for parts formed
by press working from sheet metal is used.:
[ ! ] 2．Burr height 0.1 or less
[ ! ] 3．Bend angle tolerance ±1°
[ ! ] 4．In case of the thin plates, the tap ridges may be crushed, so please be careful when tightening.
[ ! ] 5．There are machining limits for sections b, f, h, g below.
Tf (Distance between the hole and the bend)b
（Distance between
the hole and the end face）		hg
EN 1.0330 Equiv.
EN 1.0320 Equiv. (hot coiled)		EN AW−5052 Equiv.EN 1.4301 Equiv.Through HoleTapped HoleSlotted Hole parallel
to Hole Bending with Tolerance
L BendZ, Convex BendL BendZ, Convex Bend
0.8－0.823--3.5155
1.01.01.02335.53.515.55.5
1.2－1.22335.53.515.55.5
1.61.51.523.5364166
2.32.02.024.53751.577
3.23.03.026.53971.599
4.5－4.037.54118(9)21111
6.0－－314416152.51618
[ ! ] Slotted hole f parallel to T4.0 and T4.5 will be (9).
[ ! ] The hole may be deformed if specified at the limit value shown above.
[ ! ]6．There will be some scratches left by press brake. Use r, e, d dimension for reference only.
TR after BendingBrake Scratches
PositionDepth
EN 1.0330 Equiv.
EN 1.0320 Equiv. (hot coiled)		EN AW−5052 Equiv.EN 1.4301 Equiv.（r）（e）（d）
0.8－0.80.850.1
1.01.01.0150.1
1.2－1.21.250.1
1.61.51.51.560.1
2.32.02.02.07.50.1
3.23.03.03.010.50.2
4.5－4.04.013.50.3
6.0－－6.0170.5
[ ! ] If the bend and hole are close to each other, r may be smaller.
[ ! ]7．Bending causes biting and bulging.
[ ! ]8．Since it is manufactured with minimum bending R, there is a possibility of breakage if it is used in an environment where stress is concentrated, such as impact.
■Appearance per Material (Surface Treatment) and Machining Method
 NoneBlack OxideTrivalent Chromate (Clear)Trivalent Chromate (Black)
SPSPBSPUSPK
EN 1.0330 Equiv.
T0.8～3.2
EN 1.0320 Equiv. (hot coiled)
T4.5～6.0
EN 1.0038 Equiv.
（Black）
T9.0
 NoneAnodize (Clear)Anodize (Black)
AMAMWAMB
EN AW−5052 Equiv.
 None
SUD
EN 1.4301 Equiv. (Passivated 2B)
T0.8～6.0
EN 1.4301 Equiv.（No.1）
T9.0

Part Number:  

    3D preview is not available, because the part number has not yet been determined.

  • In order to open the 3D preview, the part number must be fixed.
Loading...

Plug-in is required for 3D Preview

CAD Download

Data to be displayed
30
45
60
  1. 1
Part Number
SWBAS-AM-A[20-200/1]-B[10-200/1]-T[1.5,​2,​3]
SWBAS-AMB-A[20-200/1]-B[10-200/1]-T[1.5,​2,​3]
SWBAS-AMW-A[20-200/1]-B[10-200/1]-T[1.5,​2,​3]
SWBAS-SP-A[20-200/1]-B[10-200/1]-T[1.6,​2.3,​3.2,​4.5,​6]
SWBAS-SPB-A[20-200/1]-B[10-200/1]-T[1.6,​2.3,​3.2,​4.5,​6]
SWBAS-SPK-A[20-200/1]-B[10-200/1]-T[1.6,​2.3,​3.2,​4.5,​6]
SWBAS-SPU-A[20-200/1]-B[10-200/1]-T[1.6,​2.3,​3.2,​4.5,​6]
SWBAS-SUD-A[20-200/1]-B[10-200/1]-T[1.5,​2,​3,​4]
Part NumberMinimum order quantityVolume Discount
Standard
Shipping Days
?
RoHSMaterial Surface Treatment A
(mm) 		B
(mm) 		T
(mm)
1 7 Days 10EN AW-5052 Equiv.Not Provided20 ～ 20010 ～ 2001.5 ～ 3
1 9 Days 10EN AW-5052 Equiv.Black Anodize20 ～ 20010 ～ 2001.5 ～ 3
1 9 Days 10EN AW-5052 Equiv.Clear Anodize20 ～ 20010 ～ 2001.5 ～ 3
1 7 Days 10EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled))Not Provided20 ～ 20010 ～ 2001.6 ～ 6
1 9 Days 10EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled))Black Oxide20 ～ 20010 ～ 2001.6 ～ 6
1 9 Days 10EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled))Trivalent Chromate (Black) 20 ～ 20010 ～ 2001.6 ～ 6
1 9 Days 10EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled))Trivalent Chromate (White)20 ～ 20010 ～ 2001.6 ～ 6
1 7 Days 10EN 1.4301 Equiv. (2B)Not Provided20 ～ 20010 ～ 2001.5 ～ 4

Loading...

  1. 1
 

Basic information

Type SWBAS

Configure

Clear all

8Suggestion of an applicable part number.

View Part Numbers

Some specification is not specified yet.
The part number is completed.

Basic Attributes

  • Material

    • EN AW-5052 Equiv.
    • EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled))
    • EN 1.4301 Equiv. (2B)

    Clear

  • Surface Treatment

    • Black Anodize
    • Black Oxide
    • Clear Anodize
    • Not Provided
    • Trivalent Chromate (Black)
    • Trivalent Chromate (White)

    Clear

  • A(mm)

     [20-200/1mm Unit(s)]

    Clear

  • B(mm)

     [10-200/1mm Unit(s)]

    Clear

  • T(mm)

    • 1.5
    • 1.6
    • 2
    • 2.3
    • 3
    • 3.2
    • 4
    • 4.5
    • 6

    Clear

  • Type

    • SWBAS-AM
    • SWBAS-AMB
    • SWBAS-AMW
    • SWBAS-SP
    • SWBAS-SPB
    • SWBAS-SPK
    • SWBAS-SPU
    • SWBAS-SUD

    Clear

  • Filter by CAD data type

    • 2D
    • 3D

    Clear

Filter by standard shipping days

    • All
    • 7 Days or Less
    • 9 Days or Less

    Reset

Optional Attributes

Tech Support

Technical Support
Tel：+49 69 668173-0 / FAX：+49 69 668173-360
Technical Inquiry

Payment Method

  • Payment on account
  • Pre Payment
  • PayPal

On-Demand Manufacturing

Change View

Certificates

  • ISO-9001
  • ISO-14001
  • AEO Certification
  • RoHS
  • REACH

MISUMI worldwide

Social Media

Legal notice

Copyright © MISUMI Corporation All Rights Reserved.