Sheet Metal Round Plate, BFHAF
Part Number
Once your search is narrowed to one product,
the corresponding part number is displayed here.
- Drawing / Specifications
- 3D Preview 3D preview is available after complete configuration
- Part Numbers
- Catalog
- Technical Information
■Hole Type Selection Chart
| Hole Type | Bolt Hole | Tapped Holes (Coarse) |
| Code | N | M |
| Shape Diagram |  [ ! ]For the d dimensions, refer to the "N Machining Dimensions" section below the Specifications Table |  |
| Part Number | [ M ] Material | [ S ] Surface Treatment | ||
| Type | Material Symbol | |||
| BFHAF | SP | T0.8~3.2 T4.5~6.0 T9.0 | : EN 1.0330 Equiv. : EN 1.0320 Equiv. (hot coiled) : EN 1.0038 Equiv. (Black) | － |
| SPB | Black Oxide | |||
| SPU | Trivalent Chromate (Clear) | |||
| SPK | Trivalent Chromate (Black) | |||
| AM | EN AW−5052 Equiv. | － | ||
| AMW | Anodize (Clear) | |||
| AMB | Anodize (Black) | |||
| SUD | T0.8~6.0 T9.0 | : EN 1.4301 Equiv. (Passivated 2B) : EN 1.4301 Equiv. (No.1) | － | |
Specification Table
| Part Number | − | A | − | T | − | Q | − | Hole Specification Code, Nominal | ||
| Type | − | Material Symbol | ||||||||
| BFHAF | − | SP | − | A200 | − | T2.3 | − | Q80 | − | N5 |
| Part Number | 1 mm Increments | Selection | Q | Hole Specification | ||||
| Type | Material Symbol | A | T | Code / Specify Method | ||||
| BFHAF | SP SPB SPU SPK | 30 ～ 300 | 0.8 ・ 1.0 ・ 1.2 ・ 1.6 ・ 2.3 3.2 ・ 4.5 ・ 6.0 ・ 9.0 | 0.1 mm Increments | ||||
| N | M | |||||||
| (Bolt Hole) | (Tapped Holes) | |||||||
| AM AMW AMB | 1.0 ・ 1.5 ・ 2.0 ・ 3.0 ・ 4.0 ・ 5.0 | 3・4・5 | 3・4・5 | |||||
| 6・8・10 | 6・8・10 | |||||||
| （Selection） | （Selection） | |||||||
| SUD | 0.8 ・ 1.0 ・ 1.2 ・ 1.5 ・ 2.0 3.0 ・ 4.0 ・ 5.0 ・ 6.0 ・ 9.0 | [ ! ] | [ ! ] | |||||
| [ ! ]If the specified hole location is close to the edges, the hole may be deformed but will be machined as specified if within machining limits. | ||||||||
[ ! ]N Machining Dimension Table
| N Specified Value | Through Hole Diameter (d) |
| 3 | 3.5 |
| 4 | 4.5 |
| 5 | 5.5 |
| 6 | 6.5 |
| 8 | 9 |
| 10 | 11 |
[ ! ]Hole Machining Table
[ ! ]T = 1.0 is not applicable for tapped holes to AM, AMW, or AMB
| T | N（Bolt Hole） | M（Tapped Hole） |
| 0.8 | 3・4・5・6・8・10 | Not Possible |
| 1.0、1.2 | 3 | |
| 1.5、1.6 | 3・4 | |
| 2.0、2.3 | 3・4・5・6 | |
| 3.0、3.2 | 3・4・5・6・8 | |
| 4.0～6.0 | 3・4・5・6・8・10 | |
| 9.0 | 5・6・8・10 | 5・6・8・10 |
Specifications, Machining Limits
[ ! ]1. See the diagram below for tolerances
[ ! ]3. In case of the thin plates, the tap ridges may be crushed, so please be careful when tightening.
[ ! ]4. For machining limits, see the table below
[Standard Machined Dimension Tolerances]
* Class B Tolerance stipulated in JIS B 0408, General dimensional tolerances for parts formed by press working from sheet metal is used.:
[ ! ]2. Burr height 0.1 or less| Product | Dimension Range (A Dimension) | 6 or less | Over 6, and 30 or Less | Over 30, and 120 or Less | Over 120, and 400 or Less |
| Sheet Metal (No Bending) | Tolerance (a) | ±0.1 | ±0.2 | ±0.3 | ±0.5 |
[ ! ]3. In case of the thin plates, the tap ridges may be crushed, so please be careful when tightening.
[ ! ]4. For machining limits, see the table below
| T | b | ||
| EN 1.0330 Equiv. EN 1.0320 Equiv. (hot coiled) EN 1.0038 Equiv. | |||
| EN AW−5052 Equiv. | EN 1.4301 Equiv. | ||
| 0.8 | ー | 0.8 | 1 |
| 1.0 | 1.0 | 1.0 | 1 |
| 1.2 | ー | 1.2 | 1 |
| 1.6 | 1.5 | 1.5 | 1 |
| 2.3 | 2.0 | 2.0 | 1.5 |
| 3.2 | 3.0 | 3.0 | 1.5 |
| 4.5 | 4.0 | 4.0 | 2 |
| ー | 5.0 | 5.0 | 2.5 |
| 6.0 | ー | 6.0 | 2.5 |
| 9.0 | ー | 9.0 | 4 |
■Appearance per Material (Surface Treatment) and Machining Method
| None | Black Oxide | Trivalent Chromate (Clear) | Trivalent Chromate (Black) | |
| SP | SPB | SPU | SPK | |
| EN 1.0330 Equiv. T0.8～3.2 |  |  |  |  |
| EN 1.0320 Equiv. (hot coiled) T4.5～6.0 |  |  |  |  |
| EN 1.0038 Equiv. （Black） T9.0 |  |  |  |  |
| None | Anodize (Clear) | Anodize (Black) | |
| AM | AMW | AMB | |
| EN AW−5052 Equiv. |  |  |  |
| None | |
| SUD | |
| EN 1.4301 Equiv. (Passivated 2B) T0.8～6.0 |  |
| EN 1.4301 Equiv. （No.1） T9.0 |  |
Part Number:
- In order to open the 3D preview, the part number must be fixed.
3D preview is not available, because the part number has not yet been determined.
Loading...
| Part Number | Minimum order quantity | Volume Discount | RoHS | Material | Surface Treatment | Outer Dia. A (mm) | Plate Thickness t (mm) | |
|---|---|---|---|---|---|---|---|---|
| 1 | 7 Days | 10 | EN AW-5052 Equiv. | Not Provided | 30 ～ 300 | 1 ～ 5 | ||
| 1 | 9 Days | 10 | EN AW-5052 Equiv. | Black Anodize | 30 ～ 300 | 1 ～ 5 | ||
| 1 | 9 Days | 10 | EN AW-5052 Equiv. | Clear Anodize | 30 ～ 300 | 1 ～ 5 | ||
| 1 | 7 Days | 10 | EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled)) | Not Provided | 30 ～ 300 | 1 ～ 6 | ||
| 1 | 9 Days | 10 | EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled)) | Black Oxide | 30 ～ 300 | 1 ～ 6 | ||
| 1 | 9 Days | 10 | EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled)) | Trivalent Chromate (Black) | 30 ～ 300 | 1 ～ 6 | ||
| 1 | 9 Days | 10 | EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled)) | Trivalent Chromate (White) | 30 ～ 300 | 1 ～ 6 | ||
| 1 | 7 Days | 10 | EN 1.4301 Equiv. (2B) | Not Provided | 30 ～ 300 | 1 ～ 4 |
Loading...
Basic information
| Type | BFHAF |
|---|
Configure
Basic Attributes
-
Material
- EN AW-5052 Equiv.
- EN 1.0330 Equiv. (EN 1.0320 Equiv. (hot-rolled))
- EN 1.4301 Equiv. (2B)
-
Surface Treatment
- Black Anodize
- Black Oxide
- Clear Anodize
- Not Provided
- Trivalent Chromate (Black)
- Trivalent Chromate (White)
-
Outer Dia. A(mm)
-
Plate Thickness t(mm)
-
Type
- BFHAF-AM
- BFHAF-AMB
- BFHAF-AMW
- BFHAF-SP
- BFHAF-SPB
- BFHAF-SPK
- BFHAF-SPU
- BFHAF-SUD
-
Filter by CAD data type
- 2D
- 3D
Filter by standard shipping days
-
- All
- 7 Days or Less
- 9 Days or Less
Optional Attributes
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Tech Support
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.