[Clean & Pack]Round Wire Coil Springs - O.D. Referenced Stainless Steel, UL/UTT
![[Clean & Pack]Round Wire Coil Springs - O.D. Referenced Stainless Steel, UL/UTT](http://uk.misumi-ec.com/linked/material/mech/MSM1/PHOTO/110310747629_001.jpg?$product_main$)
- Volume Discount
Three types of cleaning methods are available: degreasing, precision cleaning, and electrolytic polishing + precision cleaning. They can be ordered from one piece with the standard part number.
This eliminates the need for customer cleaning or outsourced cleaning, reducing the amount of time and effort required.
This eliminates the need for customer cleaning or outsourced cleaning, reducing the amount of time and effort required.
■Part Number for Clean & Pack Products
| ·Degreasing (Anti-rust single packing) | : Part Number SL-□□ |
| ·Precision cleaning (Degassing double packing) | : Part Number SH-□□ |
| ·Electrolytic polishing + precision cleaning (Degassing double packing) | : Part Number SHD-□□ |
| Product Part Number | Cleaning Method | Packaging Type | Effects Compared to Uncleaned Product | Environment (Standard) | Possible applications |
| SL-□□ | Degreasing | Anti-rust packing | Oil removal | General environment | Regular assembly process |
| Post battery assembly process | |||||
| SH-□□ | Precision cleaning | Degassing double packing | Oil removal Dust removal | Clean environment (Class 10 to 1,000*) | Battery assembly process |
| LCD-related post assembly process | |||||
| In-vehicle camera assembly process | |||||
| SHD-□□ | Electrolytic polishing + precision cleaning | Degassing double packing | Oil removal Dust removal Outgas reduction | Vacuum environment Clean environment (Class 10 to 1,000*) | Pre-semiconductor process |
| Liquid crystal deposition process | |||||
| Pre-OLED process |
■Notes
Cleaning also removes rust prevention oil, which may make the product more susceptible to rusting than an uncleaned product.
Please be careful about the application location and storage environment.
Cleaning also removes rust prevention oil, which may make the product more susceptible to rusting than an uncleaned product.
Please be careful about the application location and storage environment.
The series is standardized to maintain the spring constant uniformly to the same diameter.
SL-UL / SH-UL/ SHD-UL / SL-UTT / SH-UTT / SHD-UTT Type···Allowable Max. Deflection 40%
(i)Remark
- Cleaning also removes rust prevention oil, which may make the product more susceptible to rusting than an uncleaned product.
Please be careful about the application location and storage environment.
Part Number
Once your search is narrowed to one product,
the corresponding part number is displayed here.
- Drawing / Specifications
- 3D Preview 3D preview is available after complete configuration
- Part Numbers
![[Clean & Pack]Round Wire Coil Springs - O.D. Referenced Stainless Steel, UL/UTT: Related Image](http://content.misumi-ec.com/image/upload/t_msmwm_wyg/v1/p/jp/product/wysiwyg/110310747629/110310747629_001_20230801115853.gif)
Closed Ends (Both Ends Not Ground*)
Closed Ends (Both Ends Ground)
| O.D. D | ø10 or Less | 0 －0.5 mm | Free Length L | 50 or Less ±1 mm | |
| ø12 or More | 0 －0.8 mm | 60 or More ±2 mm |
| Type | [M] Material | Cleaning Method | ||||
| Cleaning Method | Cleaning Environment | Packaging Type | Packing Environment | |||
| SL-UL | SL-UTT | EN 1.4301 Equiv. (WPB) Spring Constant ±10% | Degreasing | General environment | Anti-rust packing | General environment |
| SH-UL | SH-UTT | Precision cleaning | Class 1,000* | Degassing double packing | Class 10** | |
| SHD-UL | SHD-UTT | Electrolytic polishing + precision cleaning | ||||
**US FED STD 209E, ISO 14644-1 ISO 4 Equiv.
[ ! ] Products are packed by order quantity. Ex. If the order is for 20 pieces, they are packed in one package (incl. 20 pieces).
[ ! ] See the details of degreasing, precision cleaning, and electrolytic polishing shown at the bottom of the
specification table.Specification Table
| Part Number |
| SL-UL16-80 |
| SHD-UTT16-80 |
■SL-UL·SH-UL·SHD-UL: Fmax. (allowable deflection) = L × 40%
kgf (load) = N⋅mm (spring constant) × 0.101972 × F (Deflection)
[kgf]=N × 0.101972
[ ! ] Both ends of * marked springs are not ground.
[!] Usage Count: 1 million times
● How to calculate the number of coils (reference value):
Total coils = solid length / wire diameter (d) - 1
Number of active coils = total coils - 2
* The values of the number of coils are for reference only. There may be some variations depending on the lot.
| Part Number | d | Solid Length | F | N{kgf} | |||
| Type | D−L | (Reference Value) | max. | max. | |||
| SL-UL | 2− | 5* | 0.2 | 1.65 | 2 | 0.98 | {0.1} |
| SH-UL | 10* | 0.26 | 5.07 | 4 | 1.96 | {0.2} | |
| SHD-UL | 15* | 0.26 | 5.07 | 6 | 2.94 | {0.3} | |
| 20* | 0.3 | 9.9 | 8 | 3.92 | {0.4} | ||
| 25* | 0.32 | 14.1 | 10 | 4.9 | {0.5} | ||
| 30* | 0.32 | 14.1 | 12 | 5.88 | {0.6} | ||
| SL-UL | 3− | 5* | 0.3 | 2 | 2 | 2 | {0.2} |
| SH-UL | 10* | 0.35 | 3.7 | 4 | 3.9 | {0.4} | |
| SHD-UL | 15* | 0.4 | 6.6 | 6 | 5.9 | {0.6} | |
| 20* | 0.4 | 6.6 | 8 | 7.8 | {0.8} | ||
| 25* | 0.45 | 11.7 | 10 | 9.8 | {1 } | ||
| 30* | 0.45 | 11.7 | 12 | 11.8 | {1.2} | ||
| 35* | 0.45 | 11.7 | 14 | 13.7 | {1.4} | ||
| 40* | 0.5 | 20 | 16 | 15.7 | {1.6} | ||
| SL-UL | 4− | 5* | 0.35 | 2.1 | 2 | 2 | {0.2} |
| SH-UL | 10* | 0.45 | 5.3 | 4 | 3.9 | {0.4} | |
| SHD-UL | 15* | 0.45 | 5.3 | 6 | 5.9 | {0.6} | |
| 20* | 0.5 | 8 | 8 | 7.8 | {0.8} | ||
| 25* | 0.5 | 8 | 10 | 9.8 | {1 } | ||
| 30* | 0.55 | 12.7 | 12 | 11.8 | {1.2} | ||
| 35* | 0.55 | 12.7 | 14 | 13.7 | {1.4} | ||
| 40 | 0.6 | 19.8 | 16 | 15.7 | {1.6} | ||
| 45 | 0.6 | 19.8 | 18 | 17.7 | {1.8} | ||
| 50 | 0.6 | 19.8 | 20 | 19.6 | {2 } | ||
| 60 | 0.65 | 29.9 | 24 | 23.5 | {2.4} | ||
| SL-UL | 5− | 5* | 0.4 | 2.2 | 2 | 2 | {0.2} |
| SH-UL | 10* | 0.5 | 4.75 | 4 | 3.9 | {0.4} | |
| SHD-UL | 15* | 0.5 | 4.75 | 6 | 5.9 | {0.6} | |
| 20* | 0.55 | 6.88 | 8 | 7.8 | {0.8} | ||
| 25* | 0.55 | 6.88 | 10 | 9.8 | {1 } | ||
| 30 | 0.65 | 14.95 | 12 | 11.8 | {1.2} | ||
| 35 | 0.65 | 14.95 | 14 | 13.7 | {1.4} | ||
| 40 | 0.65 | 14.95 | 16 | 15.7 | {1.6} | ||
| 45 | 0.7 | 21.7 | 18 | 17.7 | {1.8} | ||
| 50 | 0.7 | 21.7 | 20 | 19.6 | {2 } | ||
| 60 | 0.75 | 30.75 | 24 | 23.5 | {2.4} | ||
| SL-UL | 6− | 5* | 0.45 | 2.3 | 2 | 2 | {0.2} |
| SH-UL | 10* | 0.55 | 4.4 | 4 | 3.9 | {0.4} | |
| SHD-UL | 15* | 0.55 | 4.4 | 6 | 5.9 | {0.6} | |
| 20 | 0.65 | 8.5 | 8 | 7.8 | {0.8} | ||
| 25 | 0.65 | 8.5 | 10 | 9.8 | {1 } | ||
| 30 | 0.7 | 12.6 | 12 | 11.8 | {1.2} | ||
| 35 | 0.7 | 12.6 | 14 | 13.7 | {1.4} | ||
| 40 | 0.7 | 12.6 | 16 | 15.7 | {1.6} | ||
| 45 | 0.75 | 17.3 | 18 | 17.7 | {1.8} | ||
| 50 | 0.75 | 17.3 | 20 | 19.6 | {2 } | ||
| 60 | 0.8 | 24.8 | 24 | 23.5 | {2.4} | ||
| 70 | 0.8 | 24.8 | 28 | 27.5 | {2.8} | ||
| SL-UL | 8− | 10 | 0.65 | 4.6 | 4 | 3.9 | {0.4} |
| SH-UL | 15 | 0.75 | 8.3 | 6 | 5.9 | {0.6} | |
| SHD-UL | 20 | 0.75 | 8.3 | 8 | 7.8 | {0.8} | |
| 25 | 0.75 | 8.3 | 10 | 9.8 | {1 } | ||
| 30 | 0.8 | 10.4 | 12 | 11.8 | {1.2} | ||
| 35 | 0.8 | 10.4 | 14 | 13.7 | {1.4} | ||
| 40 | 0.8 | 10.4 | 16 | 15.7 | {1.6} | ||
| 45 | 0.85 | 14.5 | 18 | 17.7 | {1.8} | ||
| 50 | 0.85 | 14.5 | 20 | 19.6 | {2 } | ||
| 60 | 0.9 | 18 | 24 | 23.5 | {2.4} | ||
| 70 | 1 | 30 | 28 | 27.5 | {2.8} | ||
| 80 | 1 | 30 | 32 | 31.4 | {3.2} | ||
| SL-UL | 10− | 10 | 0.75 | 4.7 | 4 | 3.9 | {0.4} |
| SH-UL | 15 | 0.8 | 6.2 | 6 | 5.9 | {0.6} | |
| SHD-UL | 20 | 0.8 | 6.2 | 8 | 7.8 | {0.8} | |
| 25 | 0.9 | 9.5 | 10 | 9.8 | {1 } | ||
| 30 | 0.9 | 9.5 | 12 | 11.8 | {1.2} | ||
| 35 | 0.9 | 9.5 | 14 | 13.7 | {1.4} | ||
| 40 | 1 | 15.5 | 16 | 15.7 | {1.6} | ||
| 45 | 1 | 15.5 | 18 | 17.7 | {1.8} | ||
| 50 | 1 | 15.5 | 20 | 19.6 | {2 } | ||
| 60 | 1.1 | 23.7 | 24 | 23.5 | {2.4} | ||
| 70 | 1.1 | 23.7 | 28 | 27.5 | {2.8} | ||
| 80 | 1.1 | 23.7 | 32 | 31.4 | {3.2} | ||
| SL-UL | 12− | 15 | 0.9 | 6.75 | 6 | 5.9 | {0.6} |
| SH-UL | 20 | 1 | 10 | 8 | 7.8 | {0.8} | |
| SHD-UL | 25 | 1 | 10 | 10 | 9.8 | {1.0} | |
| 30 | 1.1 | 14.85 | 12 | 11.8 | {1.2} | ||
| 35 | 1.1 | 14.85 | 14 | 13.7 | {1.4} | ||
| 40 | 1.2 | 21.6 | 16 | 15.7 | {1.6} | ||
| 45 | 1.2 | 21.6 | 18 | 17.7 | {1.8} | ||
| 50 | 1.2 | 21.6 | 20 | 19.6 | {2.0} | ||
| 60 | 1.3 | 32.5 | 24 | 23.5 | {2.4} | ||
| 70 | 1.3 | 32.5 | 28 | 27.5 | {2.8} | ||
| 80 | 1.4 | 46.2 | 32 | 31.4 | {3.2} | ||
| SL-UL | 13− | 15 | 0.9 | 5.4 | 6 | 5.9 | {0.6} |
| SH-UL | 20 | 1 | 8.25 | 8 | 7.8 | {0.8} | |
| SHD-UL | 25 | 1 | 8.25 | 10 | 9.8 | {1 } | |
| 30 | 1.1 | 12.1 | 12 | 11.8 | {1.2} | ||
| 35 | 1.1 | 12.1 | 14 | 13.7 | {1.4} | ||
| 40 | 1.1 | 12.1 | 16 | 15.7 | {1.6} | ||
| 45 | 1.2 | 16.8 | 18 | 17.7 | {1.8} | ||
| 50 | 1.2 | 16.8 | 20 | 19.6 | {2 } | ||
| 60 | 1.2 | 16.8 | 24 | 23.5 | {2.4} | ||
| 70 | 1.4 | 35 | 28 | 27.5 | {2.8} | ||
| 80 | 1.4 | 35 | 32 | 31.4 | {3.2} | ||
| SL-UL | 16− | 15 | 1.1 | 7.7 | 6 | 5.9 | {0.6} |
| SH-UL | 20 | 1.1 | 7.7 | 8 | 7.8 | {0.8} | |
| SHD-UL | 25 | 1.2 | 10.8 | 10 | 9.8 | {1 } | |
| 30 | 1.2 | 10.8 | 12 | 11.8 | {1.2} | ||
| 35 | 1.3 | 14.3 | 14 | 13.7 | {1.4} | ||
| 40 | 1.3 | 14.3 | 16 | 15.7 | {1.6} | ||
| 45 | 1.4 | 19.6 | 18 | 17.7 | {1.8} | ||
| 50 | 1.4 | 19.6 | 20 | 19.6 | {2 } | ||
| 60 | 1.4 | 19.6 | 24 | 23.5 | {2.4} | ||
| 70 | 1.5 | 27 | 28 | 27.5 | {2.8} | ||
| 80 | 1.5 | 27 | 32 | 31.4 | {3.2} | ||
| SL-UL | 20− | 20 | 1.6 | 10.4 | 8 | 23.5 | {2.4} |
| SH-UL | 25 | 1.6 | 10.4 | 10 | 29.4 | {3 } | |
| SHD-UL | 30 | 1.7 | 12.8 | 12 | 35.3 | {3.6} | |
| 35 | 1.7 | 12.8 | 14 | 41.2 | {4.2} | ||
| 40 | 1.8 | 15.3 | 16 | 47.1 | {4.8} | ||
| 45 | 1.8 | 15.3 | 18 | 53 | {5.4} | ||
| 50 | 2 | 23 | 20 | 58.8 | {6 } | ||
| 60 | 2 | 23 | 24 | 70.6 | {7.2} | ||
| 70 | 2.2 | 35.2 | 28 | 82.4 | {8.4} | ||
| 80 | 2.2 | 35.2 | 32 | 94.1 | {9.6} | ||
[kgf]=N × 0.101972
[ ! ] Both ends of * marked springs are not ground.
[!] Usage Count: 1 million times
● How to calculate the number of coils (reference value):
Total coils = solid length / wire diameter (d) - 1
Number of active coils = total coils - 2
* The values of the number of coils are for reference only. There may be some variations depending on the lot.
[!] The values of solid length are for reference only. There may be some variations depending on the lot. Using it compressed to the solid length may cause deformation or break after a few uses. Be sure to use the springs within the range of the allowable deflection F max.(mm).
■SL-UTT·SH-UTT·SHD-UTT: Fmax. (allowable deflection) = L × Fa%
kgf (load) = N⋅mm (spring constant) × 0.101972 × F (Deflection)
[kgf]=N × 0.101972
● How to calculate the number of coils (reference value):
Total coils = solid length / wire diameter (d) - 1
Number of active coils = total coils - 2
* The values of the number of coils are for reference only. There may be some variations depending on the lot.
[ ! ] Both ends of * marked springs are not ground.
[!] Usage Count: 1 million times
| Part Number | d | Solid Length | F | N{kgf} | Fa% | |||
| Type | D−L | (Reference Value) | max. | Max. | ||||
| SL-UTT | 3− | 5* | 0.35 | 2.8 | 2 | 2.9 | {0.3} | 40 |
| SH-UTT | 10* | 0.4 | 4.8 | 4 | 5.9 | {0.6} | ||
| SHD-UTT | 15* | 0.45 | 8.3 | 6 | 8.8 | {0.9} | ||
| 20* | 0.45 | 8.3 | 6 | 8.8 | {0.9} | 30 | ||
| 25* | 0.5 | 14 | 8 | 11.8 | {1.2} | 32 | ||
| 30* | 0.5 | 14 | 8 | 11.8 | {1.2} | 27 | ||
| SL-UTT | 4− | 5* | 0.4 | 2.6 | 2 | 2.9 | {0.3} | 40 |
| SH-UTT | 10* | 0.45 | 3.9 | 4 | 5.9 | {0.6} | ||
| SHD-UTT | 15* | 0.5 | 6 | 6 | 8.8 | {0.9} | ||
| 20* | 0.55 | 9.4 | 8 | 11.8 | {1.2} | |||
| 25 | 0.6 | 14.4 | 10 | 14.7 | {1.5} | |||
| 30 | 0.6 | 14.4 | 10 | 14.7 | {1.5} | 33 | ||
| SL-UTT | 5− | 5* | 0.45 | 2.6 | 2 | 2.9 | {0.3} | 40 |
| SH-UTT | 10* | 0.5 | 3.6 | 4 | 5.9 | {0.6} | ||
| SHD-UTT | 15 | 0.6 | 7.5 | 6 | 8.8 | {0.9} | ||
| 20 | 0.6 | 7.5 | 8 | 11.8 | {1.2} | |||
| 25 | 0.65 | 10.7 | 10 | 14.7 | {1.5} | |||
| 30 | 0.7 | 15.4 | 12 | 17.7 | {1.8} | |||
| 35 | 0.7 | 15.4 | 14 | 20.6 | {2.1} | |||
| SL-UTT | 6− | 5* | 0.5 | 2.4 | 2 | 3.9 | {0.4} | 40 |
| SH-UTT | 10 | 0.6 | 4.2 | 4 | 7.8 | {0.8} | ||
| SHD-UTT | 15 | 0.7 | 7.4 | 6 | 11.8 | {1.2} | ||
| 20 | 0.7 | 7.4 | 8 | 15.7 | {1.6} | |||
| 25 | 0.8 | 13.6 | 10 | 19.6 | {2.0} | |||
| 30 | 0.8 | 13.6 | 12 | 23.5 | {2.4} | |||
| 35 | 0.85 | 17.5 | 14 | 27.5 | {2.8} | |||
| 40 | 0.9 | 23.4 | 16 | 31.4 | {3.2} | |||
| 45 | 0.9 | 23.4 | 18 | 35.3 | {3.6} | |||
| 50 | 0.9 | 23.4 | 18 | 35.3 | {3.6} | 36 | ||
| 60 | 1 | 41 | 18 | 35.3 | {3.6} | 30 | ||
| 70 | 1 | 41 | 24 | 47.1 | {4.8} | 34 | ||
| SL-UTT | 8− | 10 | 0.75 | 5.3 | 4 | 7.8 | {0.8} | 40 |
| SH-UTT | 15 | 0.75 | 5.3 | 6 | 11.8 | {1.2} | ||
| SHD-UTT | 20 | 0.9 | 10.4 | 8 | 15.7 | {1.6} | ||
| 25 | 0.9 | 10.4 | 10 | 19.6 | {2.0} | |||
| 30 | 1 | 17 | 12 | 23.5 | {2.4} | |||
| 35 | 1 | 17 | 14 | 27.5 | {2.8} | |||
| 40 | 1 | 17 | 16 | 31.4 | {3.2} | |||
| 45 | 1.1 | 25.3 | 18 | 35.3 | {3.6} | |||
| 50 | 1.1 | 25.3 | 20 | 39.2 | {4.0} | |||
| 60 | 1.1 | 25.3 | 24 | 47.1 | {4.8} | |||
| 70 | 1.2 | 39.6 | 28 | 54.9 | {5.6} | |||
| SL-UTT | 10− | 10 | 0.85 | 5.1 | 4 | 7.8 | {0.8} | 40 |
| SH-UTT | 15 | 0.85 | 5.1 | 6 | 11.8 | {1.2} | ||
| SHD-UTT | 20 | 1 | 9.5 | 8 | 15.7 | {1.6} | ||
| 25 | 1 | 9.5 | 10 | 19.6 | {2.0} | |||
| 30 | 1.1 | 14.3 | 12 | 23.5 | {2.4} | |||
| 35 | 1.1 | 14.3 | 14 | 27.5 | {2.8} | |||
| 40 | 1.2 | 20.4 | 16 | 31.4 | {3.2} | |||
| 45 | 1.2 | 20.4 | 18 | 35.3 | {3.6} | |||
| 50 | 1.2 | 20.4 | 20 | 39.2 | {4.0} | |||
| 60 | 1.3 | 29.9 | 24 | 47.1 | {4.8} | |||
| 70 | 1.4 | 43.4 | 24 | 47.1 | {4.8} | 34 | ||
| SL-UTT | 13− | 15 | 1 | 5.75 | 6 | 11.8 | {1.2} | 40 |
| SH-UTT | 20 | 1.2 | 10.5 | 8 | 15.7 | {1.6} | ||
| SHD-UTT | 25 | 1.2 | 10.5 | 10 | 19.6 | {2.0} | ||
| 30 | 1.3 | 15 | 12 | 23.5 | {2.4} | |||
| 35 | 1.3 | 15 | 14 | 27.5 | {2.8} | |||
| 40 | 1.4 | 20.3 | 16 | 31.4 | {3.2} | |||
| 45 | 1.4 | 20.3 | 18 | 35.3 | {3.6} | |||
| 50 | 1.5 | 27.8 | 20 | 39.2 | {4.0} | |||
| 60 | 1.5 | 27.8 | 24 | 47.1 | {4.8} | |||
| 70 | 1.6 | 38.4 | 28 | 54.9 | {5.6} | |||
| 80 | 1.6 | 38.4 | 32 | 62.8 | {6.4} | |||
| SL-UTT | 16− | 15 | 1.2 | 7.2 | 6 | 11.8 | {1.2} | 40 |
| SH-UTT | 20 | 1.3 | 9.1 | 8 | 15.7 | {1.6} | ||
| SHD-UTT | 25 | 1.3 | 9.1 | 10 | 19.6 | {2.0} | ||
| 30 | 1.4 | 12.3 | 12 | 23.5 | {2.4} | |||
| 35 | 1.5 | 16.5 | 14 | 27.5 | {2.8} | |||
| 40 | 1.6 | 21.6 | 16 | 31.4 | {3.2} | |||
| 45 | 1.6 | 21.6 | 18 | 35.3 | {3.6} | |||
| 50 | 1.7 | 28 | 20 | 39.2 | {4.0} | |||
| 60 | 1.7 | 28 | 24 | 47.1 | {4.8} | |||
| 70 | 1.8 | 36 | 28 | 54.9 | {5.6} | |||
| 80 | 1.8 | 36 | 32 | 62.8 | {6.4} | |||
| SL-UTT | 20− | 20 | 1.7 | 10.6 | 8 | 31.4 | {3.2} | 40 |
| SH-UTT | 25 | 1.8 | 12.6 | 10 | 39.2 | {4.0} | ||
| SHD-UTT | 30 | 1.8 | 12.6 | 12 | 47.1 | {4.8} | ||
| 35 | 2 | 19 | 14 | 54.9 | {5.6} | |||
| 40 | 2 | 19 | 16 | 62.8 | {6.4} | |||
| 45 | 2 | 19 | 18 | 70.6 | {7.2} | |||
| 50 | 2.2 | 27.5 | 20 | 78.5 | {8.0} | |||
| 60 | 2.2 | 27.5 | 24 | 94.1 | {9.6} | |||
| 70 | 2.3 | 34.5 | 28 | 109.8 | {11.2} | |||
| 80 | 2.4 | 40.8 | 32 | 125.5 | {12.8} | |||
[kgf]=N × 0.101972
● How to calculate the number of coils (reference value):
Total coils = solid length / wire diameter (d) - 1
Number of active coils = total coils - 2
* The values of the number of coils are for reference only. There may be some variations depending on the lot.
[!] The values of solid length are for reference only. There may be some variations depending on the lot. Using it compressed to the solid length may cause deformation or break after a few uses. Be sure to use the springs within the range of the allowable deflection F max.(mm).
[ ! ] Both ends of * marked springs are not ground.
[!] Usage Count: 1 million times
■Spring Constant (N/mm) [kgf/mm]
D12 is applicable to UY, UR, UF, SL-UL and UBB Types only. D14 is applicable to UBB Type only.
D12 is applicable to UY, UR, UF, SL-UL and UBB Types only. D14 is applicable to UBB Type only.
| Type | UV | UY | UR | UF | SL-UL SH-UL SHD-UL | SL-UTT SH-UTT SHD-UTT | UM | UH | UBB | |||||||||||||||||||
| D | ||||||||||||||||||||||||||||
| 2 | 0.05 {0.005} | 0.2 {0.02} | 0.3 {0.03} | 0.5 {0.05} | ||||||||||||||||||||||||
| 3 | 0.05 {0.005} | 0.098 {0.01} | 0.29 {0.03} | 0.49 {0.05} | 0.98 {0.1} | 1.5 {0.15} | ||||||||||||||||||||||
| 4 | 2.0 {0.2} | 2.9 {0.3} | 4.9 {0.5} | |||||||||||||||||||||||||
| 5 | ||||||||||||||||||||||||||||
| 6 | 2 {0.2} | 2.9 {0.3} | 5.9 {0.6} | 9.8 {1.0} | ||||||||||||||||||||||||
| 8 | ||||||||||||||||||||||||||||
| 10 | 0.2 {0.02} | |||||||||||||||||||||||||||
| 12 | ||||||||||||||||||||||||||||
| 13 | 9.8 {1.0} | 19.6 {2.0} | ||||||||||||||||||||||||||
| 14 | ||||||||||||||||||||||||||||
| 16 | ||||||||||||||||||||||||||||
| 20 | 0.3 {0.03} | 0.5 {0.05} | 0.98 {0.1} | 2.9 {0.3} | 3.9 {0.4} | 4.9 {0.5} | 14.7 {1.5} | 29.4 {3.0} | ||||||||||||||||||||
| Fmax. | F = L × 70% | F = L × Fa% | F = L × Fa% | F = L × 45% | F = L × 40% | F = L × Fa% | F = L × Fa% | F = L × Fa% | F = L × Fa% | |||||||||||||||||||
Alterations
| Part Number | — | (LKC) |
| SL-UL6-20 | — | LKC |
| Alterations | Code | Spec. | |||||||||||||||||||||||||||||||||||||||||||||||
 | LKC | Changes length and spring constant tolerance. (Refer to the table below)
[ ! ] Applicable to D5 or more. | |||||||||||||||||||||||||||||||||||||||||||||||
| Part Number | — | (LKC) |
| SL-UTT6-35 | — | LKC |
| Alterations | Code | Spec. | ||||||||||||||||||||||||||||||||||||||||
 | LKC | Changes length and spring constant tolerance. (Refer to the table below)
[ ! ] Applicable to D5 or more. | ||||||||||||||||||||||||||||||||||||||||
Cleaning Process· Degreasing (Part Number: SL-□□)
Working Environment: General environment | ||||||
|---|---|---|---|---|---|---|
 Alkaline warm pure water |  |  Ultrasonic pure water cleaning after cleaning with pure water *3 times | |  Dry | |  Anti-rust single packing |
· Precision cleaning (Part Number: SH-□□)
Working Environment: Class 1,000* | Working Environment: Class 10** | |||||||
|---|---|---|---|---|---|---|---|---|
Hydrocarbon cleaningRo water cleaning | |  Wash with pure water (10 MΩ·cm) after high-pressure water jet cleaning (Ro water) | |  Use pure water (13 MΩ·cm) | | Use nitrogen blow | |  Conducted on a clean bench in a Class 10** clean environment |
**US FED STD 209E, ISO 14644-1 ISO 4 Equiv.
· Electrolytic polishing + precision cleaning (Part Number: SHD-□□)
Working Environment: Class 1,000* | Working Environment: Class 10** | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
Hydrocarbon cleaning Ro water cleaning | |  Electrolytic polishing with an electrolytic polishing layer according to the material | | Wash with pure water (10 MΩ·cm) after high-pressure water jet cleaning (Ro water) | | Use warm pure water (13 MΩ·cm) | | Use nitrogen blow | | Conducted on a clean bench in a Class 10** clean environment |
**US FED STD 209E, ISO 14644-1 ISO 4 Equiv.
Packaging Example| For degreasing: (Part Number: SL-□□)  | For precision cleaning or electrolytic polishing + precision cleaning: (Part Number: SH-□□/SHD-□□)  [ ! ] Both the first and second layer packaging are degassed. |
Cleaning Effectiveness / Recommended Environment for UseCleaning Method | Product Part Number | Packaging Type | Effects Compared to Uncleaned Product | Environment (Standard) | Possible applications |
|---|---|---|---|---|---|
| Degreasing | SL-□□ | Anti-rust packing | Oil removal | General environment | Regular assembly process |
| Post battery assembly process | |||||
| Precision cleaning | SH-□□ | Degassing double packing | Oil removal Dust removal | Clean environment (Class 10 to 1,000*) | Battery assembly process |
| LCD-related post assembly process | |||||
| In-vehicle camera assembly process | |||||
| Electrolytic polishing + precision cleaning | SHD-□□ | Degassing double packing | Oil removal Dust removal Outgas reduction | Vacuum environment Clean environment (Class 10 to 1,000*) | Pre-semiconductor process |
| Liquid crystal deposition process | |||||
| Pre-OLED process |
Part Number:
- In order to open the 3D preview, the part number must be fixed.
3D preview is not available, because the part number has not yet been determined.
Loading...
| Part Number |
Standard Unit Price
| Minimum order quantity | Volume Discount | Allowable Load (Configurable Range) (N) | Max. Load (N) | Free Length L (mm) | Outer Dia. D (or D1) (mm) | Spring Constant (N/mm) | Wire Dia. (mm) | Solid Length (mm) | Cleaning Method | Tolerance Change | Allowable Deflection (mm) | Height At Maximum Load (free length - allowable deflection) (mm) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
- | 1 | Available | Quote | Up to 1.50 | 0.98 | 5 | 2 | 0.5 | 0.2 | 1.65 | Precision Cleaning | No grinding | 2 | 3 | |
- | 1 | Available | Quote | 1.51 to 4.50 | 1.96 | 10 | 2 | 0.5 | 0.26 | 5.07 | Precision Cleaning | No grinding | 4 | 6 | |
- | 1 | Available | Quote | 1.51 to 4.50 | 2.94 | 15 | 2 | 0.5 | 0.26 | 5.07 | Precision Cleaning | No grinding | 6 | 9 | |
- | 1 | Available | Quote | 1.51 to 4.50 | 3.92 | 20 | 2 | 0.5 | 0.3 | 9.9 | Precision Cleaning | No grinding | 8 | 12 | |
- | 1 | Available | Quote | 4.51 to 8.50 | 4.9 | 25 | 2 | 0.5 | 0.32 | 14.1 | Precision Cleaning | No grinding | 10 | 15 | |
- | 1 | Available | Quote | 4.51 to 8.50 | 5.88 | 30 | 2 | 0.5 | 0.32 | 14.1 | Precision Cleaning | No grinding | 12 | 18 | |
- | 1 | Available | Quote | 1.51 to 4.50 | 2 | 5 | 3 | 0.98 | 0.3 | 2 | Precision Cleaning | No grinding | 2 | 3 | |
- | 1 | Available | Quote | 1.51 to 4.50 | 3.9 | 10 | 3 | 0.98 | 0.35 | 3.7 | Precision Cleaning | No grinding | 4 | 6 | |
- | 1 | Available | Quote | 4.51 to 8.50 | 5.9 | 15 | 3 | 0.98 | 0.4 | 6.6 | Precision Cleaning | No grinding | 6 | 9 | |
- | 1 | Available | Quote | 4.51 to 8.50 | 7.8 | 20 | 3 | 0.98 | 0.4 | 6.6 | Precision Cleaning | No grinding | 8 | 12 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 9.8 | 25 | 3 | 0.98 | 0.45 | 11.7 | Precision Cleaning | No grinding | 10 | 15 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 11.8 | 30 | 3 | 0.98 | 0.45 | 11.7 | Precision Cleaning | No grinding | 12 | 18 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 13.7 | 35 | 3 | 0.98 | 0.45 | 11.7 | Precision Cleaning | No grinding | 14 | 21 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 15.7 | 40 | 3 | 0.98 | 0.5 | 20 | Precision Cleaning | No grinding | 16 | 24 | |
- | 1 | Available | Quote | 1.51 to 4.50 | 2 | 5 | 4 | 0.98 | 0.35 | 2.1 | Precision Cleaning | No grinding | 2 | 3 | |
- | 1 | Available | Quote | 1.51 to 4.50 | 3.9 | 10 | 4 | 0.98 | 0.45 | 5.3 | Precision Cleaning | No grinding | 4 | 6 | |
- | 1 | Available | Quote | 4.51 to 8.50 | 5.9 | 15 | 4 | 0.98 | 0.45 | 5.3 | Precision Cleaning | No grinding | 6 | 9 | |
- | 1 | Available | Quote | 4.51 to 8.50 | 7.8 | 20 | 4 | 0.98 | 0.5 | 8 | Precision Cleaning | No grinding | 8 | 12 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 9.8 | 25 | 4 | 0.98 | 0.5 | 8 | Precision Cleaning | No grinding | 10 | 15 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 11.8 | 30 | 4 | 0.98 | 0.55 | 12.7 | Precision Cleaning | No grinding | 12 | 18 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 13.7 | 35 | 4 | 0.98 | 0.55 | 12.7 | Precision Cleaning | No grinding | 14 | 21 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 15.7 | 40 | 4 | 0.98 | 0.6 | 19.8 | Precision Cleaning | With grinding | 16 | 24 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 17.7 | 45 | 4 | 0.98 | 0.6 | 19.8 | Precision Cleaning | With grinding | 18 | 27 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 19.6 | 50 | 4 | 0.98 | 0.6 | 19.8 | Precision Cleaning | With grinding | 20 | 30 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 23.5 | 60 | 4 | 0.98 | 0.65 | 29.9 | Precision Cleaning | With grinding | 24 | 36 | |
- | 1 | Available | Quote | 1.51 to 4.50 | 2 | 5 | 5 | 0.98 | 0.4 | 2.2 | Precision Cleaning | No grinding | 2 | 3 | |
- | 1 | Available | Quote | 1.51 to 4.50 | 3.9 | 10 | 5 | 0.98 | 0.5 | 4.75 | Precision Cleaning | No grinding | 4 | 6 | |
- | 1 | Available | Quote | 4.51 to 8.50 | 5.9 | 15 | 5 | 0.98 | 0.5 | 4.75 | Precision Cleaning | No grinding | 6 | 9 | |
- | 1 | Available | Quote | 4.51 to 8.50 | 7.8 | 20 | 5 | 0.98 | 0.55 | 6.88 | Precision Cleaning | No grinding | 8 | 12 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 9.8 | 25 | 5 | 0.98 | 0.55 | 6.88 | Precision Cleaning | No grinding | 10 | 15 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 11.8 | 30 | 5 | 0.98 | 0.65 | 14.95 | Precision Cleaning | With grinding | 12 | 18 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 11.8 | 30 | 5 | 0.98 | 0.65 | 14.95 | Precision Cleaning | With grinding | 12 | 18 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 13.7 | 35 | 5 | 0.98 | 0.65 | 14.95 | Precision Cleaning | With grinding | 14 | 21 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 13.7 | 35 | 5 | 0.98 | 0.65 | 14.95 | Precision Cleaning | With grinding | 14 | 21 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 15.7 | 40 | 5 | 0.98 | 0.65 | 14.95 | Precision Cleaning | With grinding | 16 | 24 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 15.7 | 40 | 5 | 0.98 | 0.65 | 14.95 | Precision Cleaning | With grinding | 16 | 24 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 17.7 | 45 | 5 | 0.98 | 0.7 | 21.7 | Precision Cleaning | With grinding | 18 | 27 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 17.7 | 45 | 5 | 0.98 | 0.7 | 21.7 | Precision Cleaning | With grinding | 18 | 27 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 19.6 | 50 | 5 | 0.98 | 0.7 | 21.7 | Precision Cleaning | With grinding | 20 | 30 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 19.6 | 50 | 5 | 0.98 | 0.7 | 21.7 | Precision Cleaning | With grinding | 20 | 30 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 23.5 | 60 | 5 | 0.98 | 0.75 | 30.75 | Precision Cleaning | With grinding | 24 | 36 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 23.5 | 60 | 5 | 0.98 | 0.75 | 30.75 | Precision Cleaning | With grinding | 24 | 36 | |
- | 1 | Available | Quote | 1.51 to 4.50 | 2 | 5 | 6 | 0.98 | 0.45 | 2.3 | Precision Cleaning | No grinding | 2 | 3 | |
- | 1 | Available | Quote | 1.51 to 4.50 | 3.9 | 10 | 6 | 0.98 | 0.55 | 4.4 | Precision Cleaning | No grinding | 4 | 6 | |
- | 1 | Available | Quote | 4.51 to 8.50 | 5.9 | 15 | 6 | 0.98 | 0.55 | 4.4 | Precision Cleaning | No grinding | 6 | 9 | |
- | 1 | Available | Quote | 4.51 to 8.50 | 7.8 | 20 | 6 | 0.98 | 0.65 | 8.5 | Precision Cleaning | With grinding | 8 | 12 | |
- | 1 | Available | Quote | 4.51 to 8.50 | 7.8 | 20 | 6 | 0.98 | 0.65 | 8.5 | Precision Cleaning | With grinding | 8 | 12 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 9.8 | 25 | 6 | 0.98 | 0.65 | 8.5 | Precision Cleaning | With grinding | 10 | 15 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 9.8 | 25 | 6 | 0.98 | 0.65 | 8.5 | Precision Cleaning | With grinding | 10 | 15 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 11.8 | 30 | 6 | 0.98 | 0.7 | 12.6 | Precision Cleaning | With grinding | 12 | 18 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 11.8 | 30 | 6 | 0.98 | 0.7 | 12.6 | Precision Cleaning | With grinding | 12 | 18 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 13.7 | 35 | 6 | 0.98 | 0.7 | 12.6 | Precision Cleaning | With grinding | 14 | 21 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 13.7 | 35 | 6 | 0.98 | 0.7 | 12.6 | Precision Cleaning | With grinding | 14 | 21 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 15.7 | 40 | 6 | 0.98 | 0.7 | 12.6 | Precision Cleaning | With grinding | 16 | 24 | |
- | 1 | Available | Quote | 8.51 to 16.00 | 15.7 | 40 | 6 | 0.98 | 0.7 | 12.6 | Precision Cleaning | With grinding | 16 | 24 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 17.7 | 45 | 6 | 0.98 | 0.75 | 17.3 | Precision Cleaning | With grinding | 18 | 27 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 17.7 | 45 | 6 | 0.98 | 0.75 | 17.3 | Precision Cleaning | With grinding | 18 | 27 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 19.6 | 50 | 6 | 0.98 | 0.75 | 17.3 | Precision Cleaning | With grinding | 20 | 30 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 19.6 | 50 | 6 | 0.98 | 0.75 | 17.3 | Precision Cleaning | With grinding | 20 | 30 | |
- | 1 | Available | Quote | 16.01 to 30.00 | 23.5 | 60 | 6 | 0.98 | 0.8 | 24.8 | Precision Cleaning | With grinding | 24 | 36 |
Loading...
Basic information
| Material | EN 1.4301 (WPB) Equiv. | Type | Round Wire | Properties / applications | Clean washing |
|---|---|---|---|---|---|
| Environmentally Friendly | RoHS compliant (10 substances) |
Configure
Basic Attributes
-
Allowable Load (Configurable Range)(N)
- Up to 1.50
- 1.51 to 4.50
- 4.51 to 8.50
- 8.51 to 16.00
- 16.01 to 30.00
- 30.01 to 50.00
- 50.01 to 73.00
- 73.01 to 107.00
- 107.01 to 150.00
-
Max. Load(N)
-
Free Length L(mm)
-
Outer Dia. D (or D1)(mm)
-
Spring Constant(N/mm)
-
Wire Dia.(mm)
-
Solid Length(mm)
- 1.65
- 2
- 2.1
- 2.2
- 2.3
- 2.4
- 2.6
- 2.8
- 3.6
- 3.7
- 3.9
- 4.2
- 4.4
- 4.6
- 4.7
- 4.75
- 4.8
- 5.07
- 5.1
- 5.3
- 5.4
- 5.75
- 6
- 6.2
- 6.5
- 6.6
- 6.88
- 7.2
- 7.4
- 7.5
- 7.7
- 8
- 8.25
- 8.3
- 8.5
- 9
- 9.1
- 9.4
- 9.5
- 9.9
- 10.4
- 10.5
- 10.6
- 10.7
- 10.8
- 11.7
- 12.1
- 12.3
- 12.5
- 12.6
- 12.7
- 12.8
- 13.6
- 14
- 14.1
- 14.3
- 14.4
- 14.5
- 14.95
- 15
- 15.3
- 15.4
- 15.5
- 16.5
- 16.8
- 17
- 17.3
- 17.5
- 18
- 19
- 19.6
- 19.8
- 20
- 20.3
- 20.4
- 21.6
- 21.7
- 23
- 23.4
- 23.7
- 24
- 24.8
- 25.3
- 27
- 27.5
- 27.8
- 28
- 29.9
- 30
- 30.75
- 32
- 34.5
- 35
- 35.2
- 36
- 38.4
- 39.6
- 40.8
- 41
- 43.4
-
Cleaning Method
- Degreasing
- Precision Cleaning
- Electrolytic polishing + precision cleaning
-
Tolerance Change
- No grinding
- With grinding
-
Allowable Deflection(mm)
-
Height At Maximum Load (free length - allowable deflection)(mm)
-
Type
- SH-UL
- SH-UTT
- SHD-UL
- SHD-UTT
- SL-UL
- SL-UTT
-
Filter by CAD data type
- 2D
- 3D
Optional Attributes
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Tech Support
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.