Carbide Square Alterations End Mill for Aluminum, Copper and Resin Machining
Click on this image to zoom in.
Click on this image to zoom in.
- Volume Discount
Part Number
Once your search is narrowed to one product,
the corresponding part number is displayed here.
Part Number
|
|---|
| T-SEC-ALHEM2S2 |
| T-SEC-ALHEM2S2.5 |
| Part Number |
Standard Unit Price
| Minimum order quantity | Volume Discount | Outer Diameter (D) (φ) | Flute Length (ℓ) (mm) | Figure | |
|---|---|---|---|---|---|---|---|
22.38 € | 1 | Available | 9 Days | 2 | 4 | 1 | |
22.24 € | 1 | Available | 9 Days | 2.5 | 5 | 2 |
Loading...
Specification Table
Blade Tip Shape Specification -CR/-CC/-MK/-EF
| Blade Diameter D (Selection) | -CR/-CC 0.1 mm Unit Specification | -MK 5° Unit Specification |
| 2, 2.5 | No Standard | No Standard |
| 3 | 60° to 135° | |
| 4 | 0.1 to (D−2)/2 | |
| 5 | ||
| 6 | ||
| 8 | 0.1 to 3.0 | |
| 10 | ||
| 12 | ||
| 14, 16 | ||
| 18, 20 |
[ ! ] For the standards of blade diameter (D), blade length (ℓ) and overall length (L), refer to the target model number page.
[ ! ] Bottom blade polishing is provided when machining the radius, corner C, and bottom blade flat.
[ ! ] The blade length (ℓ) and overall length (L) will be shorter by about D×0.5 (up to 5 mm) when blade tip shape machining is performed.
Click here for cutting conditions
Shank Additional Work -ZC/-LC
| Blade Diameter D (Selection) | Under-Neck Length Specification -KN 1 mm Unit Specification | Overall Length Specification -LC 1 mm Unit Specification | Fig. |
| 2 | KN ≥ ℓ+5 and KN ≤ L−23 | LC ≥ ℓ+10+3d | 1 |
| 6 to 10 | KN ≥ ℓ+5 and KN ≤ L−3d and KN ≤ ℓ+50 | 2 | |
| 12 | LC ≥ ℓ+D+3d | ||
| 16 | |||
| 20 |
[ ! ] For the standards of blade length (ℓ), overall length (L) and shank diameter (d), refer to the target model number page.
[ ! ] Specify within the range of LC ≥ KN+3d+5 when using both the under-neck length (KN) and overall length (LC) specifications.
[ ! ] When specifying the under-neck length (KN), the blade diameter of the shank relief will be −0.2 to 0.5 mm.
Click here for cutting conditions
■ Additional machining charges will be added to the unit price of the target model number.
■ When additional machining menus are combined, the respective additional machining charges will be added.
■ The quantity slide is applicable only to the target model number.
(Depending on the quantity, an estimate may be provided for the delivery date)
Specifications/Overview
| Applicable Model Number | Blade length ℓ | Number of flutes | |
| SEC−ALHEM2S | Short | 2 | Click here for product details |
| SEC−ALHEM2R | Regular | 2 | Click here for product details |
| SEC−ALHEM2L | Long | 2 | Click here for product details |
| SEC−ALHEM3S | Short | 3 | Click here for product details |
| SEC−ALHEM3R | Regular | 3 | Click here for product details |
| SEC−ALHEM4R | Regular | 4 | Click here for product details |
| SEC−ALRFR | Regular (Roughing) | 3 | Click here for product details |
| CUEM | Regular | 2 | Click here for product details |
| SEC−PLEM2R | Regular | 2 | Click here for product details |
| SEC−PLEM2EXL | Extra long | 2 | Click here for product details |
| SEC−LS−PLEM2R | Regular (Long Shank) | 2 | Click here for product details |
Alterations
Basic information
| Work Material | Aluminum / Copper / Graphite / Resin | Model | Square | Number of Flutes(sheet) | 2 |
|---|---|---|---|---|---|
| Processing Applications | Flat Surface / Side Surface / Groove / Inclined Cutting / Countersunk | Geometry | Sharp Corner | Coating | Non-Coated |
| Torsion Angle (θ) | Powerful Helix (45° to 60°) | Shank Diameter (d)(mm) | 4 | Overall Length (L)(mm) | 40 |
| Tolerance of OD(mm) | 0 ~ -0.02 |
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Tech Support
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.