SKF Bearing Components

?* Information on days to ship and prices

• • Recommendation

  

  Speedi-sleeves / Internal diameter 12~201.63mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 12~201.63
  ・Outer diameter(mm): 12.06~189.86
  ・eClass code: 23-05-92-90
  
  SKF Speedi-Sleeve provides an alternative to costly repairs for worn or damaged shafts. This thin-walled sleeve, specially developed by SKF, is simply positioned over the relevant part of the shaft and provides a smooth counterface that is optimized for radial shaft seals. Use of SKF Speedi-Sleeve can prevent the need for costly shaft treatments that may involve machining, hardening, plunge grinding or disassembly. SKF Speedi-Sleeve Gold is an enhanced version of standard SKF Speedi-Sleeve, offering improved resistance to abrasive wear.
  
  [Features]
  ・Optimized countersurface
  ・Cost effective
  ・Well-proven solution

  Starting from∗ ：	17.53 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• • Recommendation

  

  Locating rings / Internal diameter 47~460mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 47~460
  ・Outer diameter(mm): 52~1420
  ・Width(mm): 2~22
  ・eClass code: 23-05-17-90
  
  A bearing in the locating position must be secured axially in the housing. If the bearing seat in the housing and the bearing width do not match, locating (stabilizing) rings are required. Typically, two locating rings are required per housing. One ring should be placed on each side of the bearing. If only one locating ring is required, it should be installed on the same side as the lock nut.

  Starting from∗ ：	3.85 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  SKF Cylinder Rollers

  SKF

  [Specifications]
  ・Material: 1.3505 (100Cr6)
  ・Surface hardness: 58 - 65 HRC
  ・Norm: DIN 5402-1
  ・Rolling element diameter Dw(mm): 4-40

  Starting from∗ ：	0.54 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  SKF Locating Rings

  SKF

  [Specifications]
  ・Inner dimension(mm): 47-380
  ・Outer dimension(mm): 52-400
  ・Width(mm): 2-18
  ・Material: Steel
  
  A bearing in the locating position must be secured axially in the housing, if the bearing seat in the housing and the bearing width do not match, locating (stabilizing) rings are required.

  Starting from∗ ：	3.43 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Bearing Components / Internal diameter 15.926~400mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 15.926~400
  ・Outer diameter(mm): 42~360

  Starting from∗ ：	0.72 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Shim washers / Width 0.7mm

  SKF

  [Specifications]
  ・Width(mm): 0.7
  ・eClass code: 23-05-19-01
  
  SKF Machinery Shims are used to easily and reliably adjust the height of a machine. High quality shims allow accurate and long lasting height adjustments that save time and support reliable operation of the machine. Shims are supplied in packs of 10 and can be used to refill SKF Machinery Shim kits (assortments of different shim sizes and thickness).
  
  [Features]
  ・Easy to fit and remove
  ・Close tolerances for accurate adjustments
  ・Fully de-burred
  ・Supplied in packs containing 10 shims
  ・Thickness and size are clearly marked on the shim

  Starting from∗ ：	22.12 €
  Min. Shipping Days ：	12 Days

  *Unit price with basic configuration

• 

  Felt strips / eClass code 23-05-17-90

  SKF

  [Specifications]
  ・eClass code: 23-05-17-90
  
  Felt strips, and their high-temperature variants made of aluminium borosilicate, provide a simple and effective sealing solution. They accommodate relatively high shaft speeds, because a small gap forms between the felt strip and the shaft, transforming the seal into a non-contact, gap-type seal. Felt strips should be cut to the correct length and soaked in hot oil prior to being installed.
  
  [Features]
  ・Cost-effective
  ・Suitable for relatively high shaft speeds

  Starting from∗ ：	0.37 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Axial Dics

  SKF

  [Specifications]
  ・Inner dimension(mm): 6-160
  ・Outer dimension(mm): 19-200
  ・Width(mm): 1
  ・Material: Spring steel hardened
  
  Accessories thin universal washers.
  
  [Features]
  ・1mm thick
  ・Made of spring steel and hardened
  ・Can be used as shaft or housing washers for needle roller thrust bearings in the AXK series
  ・Can be used as shaft washers for bearings in the AXW series
  ・Can be used to provide a cost-effective bearing solution, if adjacent machine component are not hardened, but have adequate stiffness and the requirements to geometrical tolerances are moderate

  Starting from∗ ：	0.72 €
  Min. Shipping Days ：	12 Days

  *Unit price with basic configuration

• 

  Plummer block housings / Cast iron, Cast steel, Composite, Ductile cast iron / Outer diameter 70~380mm

  SKF

  [Specifications]
  ・Material: Cast iron, Cast steel, Composite, Ductile cast iron
  ・Outer diameter(mm): 70~380
  ・Width(mm): 32~95

  Starting from∗ ：	7.25 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Shaft Washer, Inner Centerable

  SKF

  [Specifications]
  ・Internal diameter(mm): 15~90
  ・Outer diameter(mm): 28~120
  ・eClass code: 23-05-09-03
  
  Shaft washers for cylindrical and needle roller thrust bearings are supplied as separate components. They are made of hardened carbon chromium bearing steel and have a precision-ground raceway surface and a ground bore. The washers can be combined with roller and cage thrust assemblies and housing washers to create complete bearings. SKF recommends using WS washers for high-speed applications where accurate centring of the washers is required.
  
  [Features]
  ・Enable full interchangeability of shaft washers
  ・Suitable for high-speed applications
  ・Suitable where accurate centring of washers is required
  ・811 series washers are available for needle roller thrust bearings

  Starting from∗ ：	8.97 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  L-section rings

  SKF

  [Specifications]
  ・Inside diameter: 30 mm
  ・Outside diameter: 50.5 mm
  ・eClass code:
  ・23-05-09-01
  
  Angle rings (L-shaped thrust collars) are used either with NU design cylindrical roller bearings to locate the shaft axially in one direction, or with NJ design bearings to locate the shaft axially in both directions. The rings are made of carbon chromium steel and are hardened and ground. They are supplied as separate components.
  
  [Features]
  ・Locate the shaft axially if there are no NJ or NUP design locating bearings within the product range
  ・Provide an extended inner ring seat for heavily loaded bearings in the locating position
  ・Simplify design or mounting procedures

  Starting from∗ ：	110.87 €
  Min. Shipping Days ：	12 Days

  *Unit price with basic configuration

• 

  L-section rings ECVA301 Series / Internal diameter 90mm

  SKF

  [Specifications]
  ・Inside diameter: 90 mm
  ・Outside diameter: 124 mm
  ・eClass code:
  ・23-05-09-01
  
  Angle rings (L-shaped thrust collars) are used either with NU design cylindrical roller bearings to locate the shaft axially in one direction, or with NJ design bearings to locate the shaft axially in both directions. The rings are made of carbon chromium steel and are hardened and ground. They are supplied as separate components.
  
  [Features]
  ・Locate the shaft axially if there are no NJ or NUP design locating bearings within the product range
  ・Provide an extended inner ring seat for heavily loaded bearings in the locating position
  ・Simplify design or mounting procedures

  Starting from∗ ：	233.53 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Speedi-sleeves / Internal diameter 25.4mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 25.4
  ・Width(mm): 7.95
  ・eClass code: 23-05-92-90
  
  SKF Speedi-Sleeve provides an alternative to costly repairs for worn or damaged shafts. This thin-walled sleeve, specially developed by SKF, is simply positioned over the relevant part of the shaft and provides a smooth counterface that is optimized for radial shaft seals. Use of SKF Speedi-Sleeve can prevent the need for costly shaft treatments that may involve machining, hardening, plunge grinding or disassembly. SKF Speedi-Sleeve Gold is an enhanced version of standard SKF Speedi-Sleeve, offering improved resistance to abrasive wear.
  
  [Features]
  ・Optimized countersurface
  ・Cost effective
  ・Well-proven solution

  Starting from∗ ：	19.55 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Lock washers / Steel / Internal diameter 10~280mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 10~280
  ・Outer diameter(mm): 21~362
  ・Width(mm): 1~3
  ・eClass code: 23-11-07-05
  
  MB and MBL lock washers are locking devices, used to secure KM, KML and HM .. T lock nuts onto a shaft or adapter sleeve and prevent unintentional loosening. MB .. A is a stronger version of the MB washer. The lock washers engage a keyway in the shaft or adapter sleeve thread. They lock the nut in position when one of the washer tabs is bent into one of the slots in the outside diameter of the lock nut. A new lock washer should be used each time the corresponding lock nut is installed.
  
  [Features]
  ・Simple, stable and reliable fastening element
  ・Easy to install and remove
  ・Used for KM, KML, and HM .. T lock nuts

  Starting from∗ ：	0.87 €
  Min. Shipping Days ：	12 Days

  *Unit price with basic configuration

• 

  Plummer block housings / Internal diameter 72, 150, 250mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 72, 150, 250
  ・Outer diameter(mm): 103, 140
  
  [Features]
  ・P 72:
  ・Lightweight
  ・Cost-effective
  ・Flexible bearing and housing combinations
  ・Simple to mount
  ・Protection against corrosion
  ・eClass code: 23-05-08-02
  SNL 517, SNLD 528:
  ・Easy to install
  ・Cost-effective bearing arrangement
  ・Reduce maintenance
  ・Minimize lubricant leakage
  ・eClass code: 23-05-17-01
  SYF 507, SYJ 505:
  ・Accommodate heavy loads in different directions
  ・Strong
  ・High degree of stiffness
  ・Narrow design
  ・eClass code: 23-05-08-02, 23-05-16-02

  Starting from∗ ：	9.27 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Speedi-sleeves / Internal diameter 13.995~125mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 13.995~125
  ・Outer diameter(mm): 103, 140
  ・eClass code: 23-05-92-90
  
  SKF Speedi-Sleeve provides an alternative to costly repairs for worn or damaged shafts. This thin-walled sleeve, specially developed by SKF, is simply positioned over the relevant part of the shaft and provides a smooth counterface that is optimized for radial shaft seals. Use of SKF Speedi-Sleeve can prevent the need for costly shaft treatments that may involve machining, hardening, plunge grinding or disassembly. SKF Speedi-Sleeve Gold is an enhanced version of standard SKF Speedi-Sleeve, offering improved resistance to abrasive wear.[Features]
  ・Optimized countersurface
  ・Cost effective
  ・Well-proven solution

  Starting from∗ ：	19.51 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  SKF Y-Bearing Seating Rings

  SKF

  [Specifications]
  ・Internal diameter(mm): 40~80
  ・eClass code: 23-05-08-02
  
  Rubber seating rings in the RIS 2 series are primarily intended to cushion insert bearings in pressed steel pillow (plummer) block housings. Located between the bearing outer ring and housing bore, they dampen vibration and noise and enable the bearings to be displaced slightly in their housings and to accommodate minor shaft expansion or misalignment.
  
  [Features]
  ・Cushion the insert bearing
  ・Dampen vibrations and noise
  ・Accommodate slight misalignment

  Starting from∗ ：	3.22 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Running Disc

  SKF

  [Specifications]
  ・Internal diameter(mm): 10~90
  ・Outer diameter(mm): 24~120
  ・eClass code: 23-05-09-03
  
  Universal washers for cylindrical and needle roller thrust bearings are supplied as separate components. They are made of hardened carbon chromium bearing steel and their raceway surface is ground, while all other surfaces are turned. The washers are suitable for applications where accurate centring of the washers is not necessary or where low speeds are involved. They can be used as shaft or housing washers for AXK series bearings, and as shaft washers for AXW series bearings.
  
  [Features]
  ・Enable full interchangeability of washers
  ・Suitable where accurate centring of washers is not necessary
  ・Suitable for low-speed applications
  ・Available for cylindrical roller thrust bearings in the K 811 series

  Starting from∗ ：	4.02 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Locating rings / Internal diameter 82mm

  SKF

  [Specifications]
  ・Inside diameter: 82 mm
  ・Outside diameter: 90 mm
  ・eClass code:
  ・23-05-17-90
  
  A bearing in the locating position must be secured axially in the housing. If the bearing seat in the housing and the bearing width do not match, locating (stabilizing) rings are required. Typically, two locating rings are required per housing. One ring should be placed on each side of the bearing. If only one locating ring is required, it should be installed on the same side as the lock nut.

  Starting from∗ ：	6.42 €
  Min. Shipping Days ：	12 Days

  *Unit price with basic configuration

• 

  Lock washers / Internal diameter 160mm

  SKF

  [Specifications]
  ・Bore diameter: 160 mm
  ・Outside diameter: 199 mm
  ・eClass code:
  ・23-11-07-05
  
  MB and MBL lock washers are locking devices, used to secure KM, KML and HM .. T lock nuts onto a shaft or adapter sleeve and prevent unintentional loosening. MB .. A is a stronger version of the MB washer. The lock washers engage a keyway in the shaft or adapter sleeve thread. They lock the nut in position when one of the washer tabs is bent into one of the slots in the outside diameter of the lock nut. A new lock washer should be used each time the corresponding lock nut is installed.
  
  [Features]
  ・Simple, stable and reliable fastening element
  ・Easy to install and remove
  ・Used for KM, KML, and HM .. T lock nuts

  Starting from∗ ：	50.45 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  L-section rings EC Series / Internal diameter 55mm

  SKF

  [Specifications]
  ・Bore diameter: 55mm
  ・Outside diameter: 77.5 mm
  ・eClass code:
  ・23-05-09-01
  
  Angle rings (L-shaped thrust collars) are used either with NU design cylindrical roller bearings to locate the shaft axially in one direction, or with NJ design bearings to locate the shaft axially in both directions. The rings are made of carbon chromium steel and are hardened and ground. They are supplied as separate components.
  
  [Features]
  ・Locate the shaft axially if there are no NJ or NUP design locating bearings within the product range
  ・Provide an extended inner ring seat for heavily loaded bearings in the locating position
  ・Simplify design or mounting procedures

  Starting from∗ ：	125.68 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Plummer block housings / Composite / Outer diameter 164mm

  SKF

  [Specifications]
  ・Material: Composite
  ・Outer diameter(mm): 164
  ・eClass code: 23-05-08-02
  
  Pillow (plummer) block housings are designed to accommodate an insert bearing. Housings made of composite materials are lightweight but robust and have excellent corrosion resistance. They are suitable for most applications and can be bolted directly to a support surface.
  
  [Features]
  ・Excellent corrosion resistance
  ・Tolerant of high and low temperatures
  ・Lightweight
  ・Recyclable

  Starting from∗ ：	14.88 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Plummer block housings M Series / Cast iron / Outer diameter 219mm

  SKF

  [Specifications]
  ・Material: Cast iron
  ・Outer diameter(mm): 219
  ・eClass code: 23-05-08-02
  
  Pillow (plummer) block housings are designed to accommodate an insert bearing. The cast iron housings are strong, stiff and cost-effective. They are suitable for most applications and can be bolted directly to a support surface.
  
  [Features]
  ・Accommodate heavy loads in different directions
  ・High degree of stiffness
  ・Narrow design

  Starting from∗ ：	39.13 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Tools

  SKF

  [Specifications]
  ・Case dimensions (l x h x w): 530 x 110 x 360 mm
  ・eClass code: 23-05-19-01
  
  SKF Machinery Shims are used to easily and reliably adjust the height of a machine. This assortment of high quality metric shims allows accurate and long lasting height adjustments of a very wide range of machines. SKF Machinery Shims help technicians to save time and support the reliable operation of their machine.
  
  [Features]
  ・Comprehensive assortment for many applications
  ・Easy to fit and remove
  ・Close tolerances for accurate adjustments
  ・Thickness and size are clearly marked on the shim and in the case
  ・Shim kit can be refilled with shim packs

  Starting from∗ ：	1,374.28 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Tools M / MV Series

  SKF

  [Specifications]
  ・Coil diameter: 140 mm
  ・Colour: Grey, Black
  ・eClass code: 23-05-19-01
  
  The SKF TIH 220M is a large induction heater and is designed for the hot mounting of bearings. This versatile heater is ideal for use on workbenches and can easily be transported to on-site applications with the optional heater trolley TIH T1. The heater has a convenient sliding yoke and is supplied with an additional smaller yoke. The TIH 220M can heat bearings with a minimum bore diameter of 60 mm and larger bearings with a maximum weight of 300 kg.
  
  [Features]
  ・Supplied with standard sliding yoke and one smaller yoke located in an integrated storage compartment
  ・Easy and safe to use with automatic temperature control or time controlled heating
  ・Automatic demagnetization reduces risk of bearing contamination
  ・Suitable for non-bearing applications for workpieces weighing up to 150 kg
  ・Automatic temperature hold function to keep the bearing hot after completion of the heating cycle

  Starting from∗ ：	9,897.73 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  L-section rings EC Series / Internal diameter 40mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 40
  ・Outer diameter(mm): 54.1
  ・Width(mm): 8.5
  ・eClass code: 23-05-09-01
  
  Angle rings (L-shaped thrust collars) are used either with NU design cylindrical roller bearings to locate the shaft axially in one direction, or with NJ design bearings to locate the shaft axially in both directions. The rings are made of carbon chromium steel and are hardened and ground. They are supplied as separate components.
  
  [Features]
  ・Locate the shaft axially if there are no NJ or NUP design locating bearings within the product range
  ・Provide an extended inner ring seat for heavily loaded bearings in the locating position
  ・Simplify design or mounting procedures

  Starting from∗ ：	68.30 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  L-section rings ECVA301 Series / Internal diameter 70, 75mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 70, 75
  ・Outer diameter(mm): 97.4, 104
  ・Width(mm): 15.5, 16.5

  Starting from∗ ：	156.37 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Plummer block housings M Series / Cast iron / Outer diameter 127, 130, 160mm

  SKF

  [Specifications]
  ・Material: Cast iron, Cast steel, Composite, Ductile cast iron
  ・Outer diameter(mm): 127, 130, 160
  ・eClass code: 23-05-08-02
  
  Pillow (plummer) block housings are designed to accommodate an insert bearing. The cast iron housings are strong, stiff and cost-effective. They are suitable for most applications and can be bolted directly to a support surface.
  
  [Features]
  ・Accommodate heavy loads in different directions
  ・High degree of stiffness
  ・Narrow design

  Starting from∗ ：	14.55 €
  Min. Shipping Days ：	12 Days

  *Unit price with basic configuration

• 

  Shim washers / Width 0.2, 0.4mm

  SKF

  [Specifications]
  ・Width(mm): 0.2, 0.4
  ・eClass code: 23-05-08-02
  
  SKF Machinery Shims are used to easily and reliably adjust the height of a machine. High quality shims allow accurate and long lasting height adjustments that save time and support reliable operation of the machine. Shims are supplied in packs of 10 and can be used to refill SKF Machinery Shim kits (assortments of different shim sizes and thickness).
  
  [Features]
  ・Easy to fit and remove
  ・Close tolerances for accurate adjustments
  ・Fully de-burred
  ・Supplied in packs containing 10 shims
  ・Thickness and size are clearly marked on the shim

  Starting from∗ ：	18.80 €
  Min. Shipping Days ：	12 Days

  *Unit price with basic configuration

• 

  Washers / Internal diameter 24~170mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 24~170
  ・Outer diameter(mm): 35~220
  ・eClass code: 23-05-10-01
  
  Sphered seat washers are used together with thrust ball bearings with sphered housing washers when the bearing is fitted into a machine component manufactured with a flat surface. The seat washers are supplied as separate components. Depending on bearing series, they have the basic designation U 2, U 3 or U 4 followed by a two-digit number, which identifies the size, e.g. sphered seat washer U 320 for bearing 53320.
  
  [Features]
  ・Enable the bearings to accommodate initial misalignment
  ・Can be used with single or double direction bearings
  ・Enable full interchangeability of seat washers

  Starting from∗ ：	18.08 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Bearing Components EC Series

  SKF

  [Specifications]
  ・Internal diameter(mm): 50
  ・Outer diameter(mm): 71.4
  ・eClass code: 23-05-09-01
  
  Angle rings (L-shaped thrust collars) are used either with NU design cylindrical roller bearings to locate the shaft axially in one direction, or with NJ design bearings to locate the shaft axially in both directions. The rings are made of carbon chromium steel and are hardened and ground. They are supplied as separate components.
  
  [Features]
  ・Locate the shaft axially if there are no NJ or NUP design locating bearings within the product range
  ・Provide an extended inner ring seat for heavily loaded bearings in the locating position
  ・Simplify design or mounting procedures

  Starting from∗ ：	117.38 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Bearing Components M Series

  SKF

  [Specifications]
  ・Outer diameter(mm): 203
  ・eClass code: 23-05-08-02
  
  Pillow (plummer) block housings are designed to accommodate an insert bearing. The cast iron housings are strong, stiff and cost-effective. They are suitable for most applications and can be bolted directly to a support surface.
  
  [Features]
  ・Accommodate heavy loads in different directions
  ・High degree of stiffness
  ・Narrow design

  Starting from∗ ：	29.30 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Locating rings / Internal diameter 101~350mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 101~350
  ・Outer diameter(mm): 110~370
  ・eClass code: 23-05-17-90
  
  A bearing in the locating position must be secured axially in the housing. If the bearing seat in the housing and the bearing width do not match, locating (stabilizing) rings are required. Typically, two locating rings are required per housing. One ring should be placed on each side of the bearing. If only one locating ring is required, it should be installed on the same side as the lock nut.

  Starting from∗ ：	7.22 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Lock washers / Internal diameter 27.5mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 27.5
  ・Outer diameter(mm): 49
  ・eClass code: 23-11-07-05
  
  MB and MBL lock washers are locking devices, used to secure KM, KML and HM .. T lock nuts onto a shaft or adapter sleeve and prevent unintentional loosening. MB .. A is a stronger version of the MB washer. The lock washers engage a keyway in the shaft or adapter sleeve thread. They lock the nut in position when one of the washer tabs is bent into one of the slots in the outside diameter of the lock nut. A new lock washer should be used each time the corresponding lock nut is installed.
  
  [Features]
  ・Simple, stable and reliable fastening element
  ・Easy to install and remove
  ・Used for KM, KML, and HM .. T lock nuts

  Starting from∗ ：	0.95 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Plummer block housings M Series / Outer diameter 152, 187mm

  SKF

  [Specifications]
  ・Outer diameter(mm): 152, 187
  ・eClass code: 23-05-08-02
  
  Pillow (plummer) block housings are designed to accommodate an insert bearing. The cast iron housings are strong, stiff and cost-effective. They are suitable for most applications and can be bolted directly to a support surface.
  
  [Features]
  ・Accommodate heavy loads in different directions
  ・High degree of stiffness
  ・Narrow design

  Starting from∗ ：	16.82 €
  Min. Shipping Days ：	12 Days

  *Unit price with basic configuration

• 

  Housing Washer, Housing Locating

  SKF

  [Specifications]
  ・Internal diameter(mm): 16~92
  ・Outer diameter(mm): 28~120
  
  Housing washers for cylindrical and needle roller thrust bearings are supplied as separate components. They are made of hardened carbon chromium bearing steel and have a precision-ground raceway surface and a ground outside surface. The washers can be combined with roller and cage thrust assemblies and shaft washers to create complete bearings. SKF recommends using GS washers for high-speed applications where accurate centring of the washers is required.
  
  [Features]
  ・Enable full interchangeability of housing washers
  ・Suitable for high-speed applications
  ・Suitable where accurate centring of washers is required
  ・811 series washers are available for needle roller thrust bearings

  Starting from∗ ：	8.97 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

Loading...